Bedienungsanleitung Black Decker KR704 (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

461871

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingthesidehandleanddepthstop(g.A)

u Turn the grip counterclockwise until you can slide the side

handle (8) onto the front of the tool as shown.

u Rotate the side handle into the desired position.

u Insert the depth stop (7) into the mounting hole as shown.

u Set the drilling depth as described below.

u Tighten the side handle by turning the grip clockwise.

Fittingadrillbitorscrewdriverbit(g.B&C)

Keylesschuckwithspindlelock(g.B)

u Open the chuck by turning the sleeve (9) counterclockwise.

u Insert the bit shaft (10) into the chuck.

u Tighten the chuck by turning the sleeve clockwise.

Keyedchuck(g.C)

u Open the chuck by turning the sleeve (11)

counterclockwise.

u Insert the bit shaft (10) into the chuck.

u Insert the chuck key (12) into each hole (13) in the side of

the chuck and turn clockwise until tight.

Removingandrettingthechuck(g.D)

u Open the chuck as far as possible.

u Remove the chuck retaining screw, located in the chuck,

by turning it clockwise using a screwdriver.

u Tighten an Allen key into the chuck and strike it with

a hammer as shown.

u Remove the Allen key.

u Remove the chuck by turning it counterclockwise.

u To ret the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Selecting the direction of rotation

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(4) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

u For drilling in masonry, set the drilling mode selector (5) to

the position.

u For drilling in other materials and for screwdriving, set the

drilling mode selector (5) to the position.

Settingthedrillingdepth(g.A)

u Slacken the side handle (8) by turning the grip

counterclockwise.

u Set the depth stop (7) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

u Tighten the side handle by turning the grip clockwise.

Switching on and off

u To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

If the tool has a variable speed control knob (3), set it to

the required speed range. As a general rule, use low

speeds for large diameter drill bits and high speeds for

smaller diameter drill bits.

u For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available

only at full speed or at any speed preset with the variable

speed control knob (3). This option does not work in

reverse rotation.

u To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Accessories

The performance of your tool depends on the accessory used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR704 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info