Bedienungsanleitung Black Decker kr910k (Seite 6 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388843

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

(Original instructions)

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Variable speed control switch

4. Forward/reverse slider

5. Two-gear selector

6. Drilling mode selector

7. Keyless chuck with spindle lock

7. Keyless chuck

7. Keyed chuck

8. Depth stop

9. Side handle

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle and depth stop (g. A)

u Turn the grip counterclockwise until you can slide the side

handle (9) onto the front of the tool as shown.

u Rotate the side handle into the desired position.

u Insert the depth stop (8) into the mounting hole as shown.

u Set the drilling depth as described below.

u Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit (g. B - D)

Keyless chuck with spindle lock (g. B)

u Open the chuck by turning the sleeve (10) counterclockwise.

u Insert the bit shaft (11) into the chuck.

u Tighten the chuck by turning the sleeve clockwise.

Keyless chuck (g. C)

u Open the chuck by turning the front part (12) with one

hand while holding the rear part (13) with the other.

u Insert the bit shaft (11) into the chuck and rmly tighten

the chuck.

Keyed chuck (g. D)

u Open the chuck by turning the sleeve (14) counterclockwise.

u Insert the bit shaft (11) into the chuck.

u Insert the chuck key (15) into each hole (16) in the side of

the chuck and turn clockwise until tight.

Removing and retting the chuck (g. E & F)

u Open the chuck as far as possible.

u Remove the chuck retaining screw, located in the chuck,

by turning it clockwise using a screwdriver.

u Tighten an Allen key into the chuck and strike it with

a hammer as shown.

u Remove the Allen key.

u Remove the chuck by turning it counterclockwise.

u To ret the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Selecting the direction of rotation

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse switch

(4) to the right.

u To select reverse rotation, push the forward/reverse switch

(4) to the left.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

u For drilling in masonry, set the drilling mode selector (6) to

the position.

u For drilling in other materials and for screwdriving, set the

drilling mode selector (6) to the position.

Two-gear selector (g. G)

u For drilling in steel and for screwdriving applications, turn

the two-gear selector (5) into position 1 by aligning the

number with the recess (17) (1st gear).

u For drilling in materials other than steel, turn the two-gear

selector (5) into position 2 by aligning the number with the

recess (17) (2nd gear).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kr910k Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info