Bedienungsanleitung Black Decker ks 531 k (Seite 21 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

382777

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

OPERATING YOUR JIGSAW

To switch your jigsaw on, fully squeeze the on/off

trigger switch (1). To switch your jigsaw off, release

the trigger switch (1). When plugging your jigsaw in,

ensure the trigger switch is in the OFF position.

When continuous operation is required, squeeze the

trigger and depress the lock on button (2) and release

the trigger. To disengage the lock, squeeze and release

the trigger. Always disengage the lock before

disconnecting from the power supply.

SAW SHOE ADJUSTMENT FOR ANGULAR CUTTING

The shoe plate (5) can be angled up to 45˚ on either side.

To do this, disconnect your jigsaw from the power supply.

Raise the dust shroud (3)

and loosen both screws on

the shoe plate with a

screwdriver. Pull the shoe

plate backward a little, and

set the desired angular

adjustment according to the

scale or push the shoe plate

forward for fixed locks at 0˚,

15˚, 30˚, or 45˚. Tighten the

screws to secure. Although

the scale and notches are

accurate for most purposes

it is advisable for very

accurate angle cutting to use a protractor to set the

shoe. Make a test cut on some scrap material to check

the accuracy of the angle. To reset the shoe for a

square cut, slacken the clamp screws and move the

shoe until it is approximately 90˚ to the blade, and then,

whilst applying slight forward pressure on the shoe,

retighten the clamp screws.

DUST EXTRACTION

Your jigsaw with a hose adapter (accessory part), can

be fitted to most portable vacuum cleaners.

To utilise this facility push

adapter into the aperture at

the rear of jigsaw and fit

vacuum hose in or over the

adapter, depending on the

hose size. The dust shroud

should be in a downwards position.

HANDY HINTS

Cutting laminates

The blades of your jigsaw cut on the upstroke so any

tendency for edge splintering will occur on the face of

the material nearest the saw shoe. When sawing thin

wood or plastic laminates, use a fine tooth metal

cutting blade and cut from the back surface of the

material. To minimise the risk of chipping the edges of

plastic laminate, clamp a piece of scrap wood

or hardboard to both sides of the laminate to form a

sandwich, and saw through the complete assembly.

Always select the right blade for the job.

Pocket cutting

The saw blade can be inserted directly into a wood

surface without first drilling a pilot hole, thus

eliminating a drilling operation.

First measure and clearly mark the surface to be cut.

Then tip your jigsaw forward so that the rounded tips of

the shoe rest on the work surface but with the blade

well clear of it. Switch your jigsaw on and move the

saw down until the moving blade is exactly over the

chosen point of entry. Lower the rear of the shoe down

towards the work slowly, maintaining a firm pivoting

pressure on the shoe tips with the blade exactly on the

required line. Do not move your jigsaw forward along

the cut line until the saw blade has completely

entered the material and the shoe comes to rest flat

on its surface.

Cutting metal

Your jigsaw can be used for cutting light gauge ferrous

sheet and non-ferrous metals such as copper, brass,

aluminium, etc. It is advisable when cutting thin sheet

to clamp a backing sheet of soft wood or plywood to

the work as this will enable you to obtain a clean cut

without vibration and the possibility of tearing the

metal. Both metal and wood backing are sawn

together. Do not force the cutting blade into the metal

as this will reduce the life of the blade and possibly

damage the motor. Cutting thin metal will take longer

than cutting even a relatively thick piece of wood, so

do not be tempted to speed up the operation by

forcing the saw. Spread a thin film of oil along the

proposed cutting line before commencing to saw

metal. Always select the right blade for the job.

Cleaning

Disconnect your jigsaw from the power supply. Use

only mild soap and a slightly damp cloth to clean

your jigsaw. Many household cleaners contain

chemicals which could seriously damage the

plastic. Also, do not use petrol, turpentine, lacquer

or paint thinners or similar products. Never let any

liquid get inside the tool and never immerse any part

of your jigsaw into liquid.

ENGLISH

CD300 KS531 ML p01-31 22-09-2000, 11:4321

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ks 531 k Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info