Bedienungsanleitung Black Decker ks 66 l gb (Seite 7 von 12) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

382813

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Safety instructions for saws with a pendulum blade

guard

◆ Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie

the lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and make sure it

moves freely and does not touch the blade or any other

part, in all angles and depths of cut.

◆ Check the operation of the lower guard spring.

If the guard and the spring are not operating

properly, they must be serviced before use. Lower

guard may operate sluggishly due to damaged parts,

gummy deposits, or a build-up of debris.

◆ Lower guard should be retracted manually only for

special cuts such as “plunge cuts” and “compound

cuts.” Raise lower guard by retracting handle and

as soon as blade enters the material, the lower

guard must be released. For all other sawing, the lower

guard should operate automatically.

◆ Always observe that the lower guard is covering

the blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause the saw

to walk backwards, cutting whatever is in its path.

Be aware of the time it takes for the blade to stop after

switch is released.

Additional safety instructions for all saws with riving

knife

◆ Use the appropriate riving knife for the blade being

used. For the riving knife to work, it must be thicker than

the body of the blade but thinner than the tooth set of the

blade.

◆ Adjust the riving knife as described in this

instruction manual. Incorrect spacing, positioning and

alignment can make the riving knife ineffective in

preventing kickback.

◆ Always use the riving knife except when plunge

cutting. Riving knife must be replaced after plunge

cutting. Riving knife causes interference during plunge

cutting and can create kickback.

◆ For the riving knife to work, it must be engaged in

the workpiece. The riving knife is ineffective in

preventing kickback during short cuts.

◆ Do not operate the saw if riving knife is bent. Even a

light interference can slow the closing rate of a guard.

Additional safety instructions for circular saws

◆ Wear ear protectors. Exposure to noise can cause

hearing loss.

◆ Warning! Contact with or inhalation of dusts arising

from cutting applications may endanger the health of the

operator and possible bystanders. Wear a dust mask

specifically designed for protection against dust and

fumes and ensure that persons within or entering the

work area are also protectedical safety

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Additional safety instructions for lasers

Warning! Laser radiation.

Do not look into the laser beam.

Do not view the laser beam directly with optical

instruments.

Refer to the laser product characteristics.

◆ This laser complies with class 2 according to EN60825-1:1

1994+A11. Do not replace a laser diode with a different

type. If damaged, have the laser repaired by an authorised

repair agent.

◆ Do not use the laser for any purpose other than projecting

laser lines.

◆ An exposure of the eye to the beam of a class 2 laser is

considered safe for a maximum of 0.25 seconds.

Eyelid reflexes will normally provide adequate protection.

At distances over 1 m, the laser complies with class 1 and

thus is considered completely safe.

◆ Never look into the laser beam directly and intentionally.

◆ Do not use optical tools to view the laser beam.

◆ Do not set up the tool at a position where the laser beam

can cross any person at head height.

◆ Do not let children come near the laser.

Warning! This tool is intended for indoor use only.

Do not use the tool for outdoor applications.

Overview

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Spindle lock button

6. Laser on/off switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ks 66 l gb Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info