Bedienungsanleitung Black Decker ks 66 l qs (Seite 8 von 12) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

383710

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

7. Laser aperture

8. Shoe

9. Saw blade

10. Saw blade guard

11. Riving knife

12. Saw dust outlet

Assembly and adjustment

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and

that the saw blade has stopped.

Removing and fitting a saw blade (fig. A)

Removing

◆ Keep the spindle lock button (5) depressed and rotate the

blade until the spindle lock engages.

◆ Loosen and remove the blade retaining screw (13) by turning

it counterclockwise using the spanner (14) supplied.

◆ Remove the outer washer (15).

◆ Remove the saw blade (9).

Fitting

◆ Place the saw blade onto the inner flange (16), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

◆ Fit the outer washer (15) on the spindle, with the raised

part pointing away from the saw blade.

◆ Insert the blade retaining screw (13) into the hole.

◆ Keep the spindle lock button (5) depressed.

◆ Securely tighten the blade retaining screw by turning it

clockwise using the spanner (14) supplied.

◆ Adjust the riving knife as described below.

Adjusting the riving knife (fig. B)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

◆ Loosen the screws (17), using the spanner (14), while holding

the riving knife in position.

◆ Position the riving knife (11) as shown.

◆ The distance between the toothed rim and the riving knife

should be 2 - 3 mm.

◆ The height difference between the toothed rim and the

lower end of the riving knife should be 2 - 3 mm.

◆ Tighten the screws.

Fitting and removing the parallel fence (fig. C)

The parallel fence is used to saw in a straight line parellel to

the edge of the workpiece.

Fitting

◆ Loosen the locking knob (18).

◆ Insert the parallel fence (19) through the openings (20).

◆ Slide the parallel fence into the desired position.

◆ Tighten the locking knob.

Removing

◆ Loosen the locking knob.

◆ Pull the parallel fence off the tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

This tool can be used in the right hand or the left hand.

Adjusting the sawing angle (fig. D)

The default angle between the saw blade and the shoe is 90°.

◆ Use a square to check that the angle between the saw

blade and the shoe is 90°. If the angle does not measure

90° adjust as follows:

◆ Loosen the locking knob (21) to unlock the saw shoe.

◆ Loosen the locknut (22) on the adjusting screw (23).

◆ Screw the adjusting screw in or out to achieve a 90° angle.

◆ Retighten the locknut.

◆ Tighten the locking knob to lock the saw shoe in place.

Adjusting the depth of cut (fig. E)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx. 2 mm.

◆ Loosen the knob (24) to unlock the saw shoe.

◆ Move the saw shoe (8) into the desired position. The

corresponding depth of cut can be read from the scale (25).

◆ Tighten the knob to lock the saw shoe in place.

Adjusting the mitre angle (fig. F)

This tool can be set to mitre angles between 0° and 45°.

◆ Loosen the locking knob (21) to unlock the saw shoe.

◆ Move the saw shoe (8) into the desired position. The

corresponding mitre angle can be read from the scale (26).

◆ Tighten the locking knob to lock the saw shoe in place.

Switching on and off

◆ To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

◆ To switch the tool off, release the on/off switch.

Sawing

Always hold the tool with both hands.

◆ Let the blade run freely for a few seconds before starting

the cut.

◆ Apply only a gentle pressure to the tool while performing

the cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ks 66 l qs Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info