Bedienungsanleitung Black Decker ks 855 n (Seite 25 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

382820

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

• Make sure that you remove the blade-changing

spanner from the saw blade locking screw before

you switch on the circular saw.

• Do not switch off the power tool unless the saw

blade is running freely.

When sawing

• Only hold your saw by the handles provided. Do not

hold your saw in a position that could result in a

poor grip and control of the saw.

• Always ensure that there is sufficient clearance

below the material being cut and the bench or

support to allow the safety guard to rotate fully.

• All nails and metal objects must be removed from

the workpiece before you commence sawing.

• Do not attempt to saw extremely small workpieces.

• After switching off, never attempt to stop the

saw blade by pressing against the side of the blade.

• Never put the circular saw down on a table or work

bench unless you have previously switched off.

• Never operate the circular saw with the saw blade

turned upwards or to the side.

Operational protection devices

• Ensure that all devices screening the saw blade are

in perfect working order.

• Never jam the saw guard.

• Free a jammed saw guard immediately and do not

use the saw if the guard is jammed.

• Only use the guard retracting lever provided should

the blade guard need to be moved when

commencing a cut.

• The riving knife must not be removed.

• The riving knife should be correctly set.

Checking and changing the saw blade

• Only saw blades conforming to the specifications

contained in these operating instructions may

be used.

• Saw blades whose main part is thicker or whose

pitch is smaller than the riving knife’s thickness

should not be used.

• Saw blades made of high alloy, high speed steel

(HSS steel) should not be used.

• Only sharp saw blades in perfect working condition

should be used; cracked or bent saw blades should

be discarded and replaced at once.

• Ensure that the saw blade is securely fixed and

turns in the correct direction.

• Metal cutting and stone cutting discs should not be

used with this saw.

Save these instructions!

DOUBLE INSULATION

The tool is double insulated. This means that all

the external metal parts are electrically insulated

from the mains power supply. This is done by

placing insulation barriers between the

electrical and mechanical components making it

unnecessary for the tool to be earthed.

Note: Double insulation does not take the place

of normal safety precautions when operating the

tool. The insulation system is for added protection

against injury resulting from a possible electrical

insulation failure within the tool.

ELECTRICAL SAFETY

Be sure the supply is the same as the voltage given on

the rating plate. The tool is fitted with a two-core cable

and plug.

MAINS PLUG REPLACEMENT (UK ONLY)

Should the mains plug need replacing and you are

competent to do this, proceed as instructed below.

If you are in doubt, contact a Black & Decker service

agent or a qualified electrician.

• Disconnect the plug from the power supply.

• Cut off the plug and dispose of safely. A plug with

bared copper conductors is very dangerous if

engaged in a live socket outlet.

• Only fit BS1363A approved plugs fitted with the

correctly rated fuse.

Note: Fuses do not give personal protection against

electric shock.

• The cable wire colours, or a letter, will be marked at

the connection point of most good quality plugs. Attach

the wires to their respective points in the plug (see

diagram). Brown is L (live) and blue is N (neutral).

Fit a plug

approved

to BS1363A

Connect

blue to

N (neutral)

Make sure that

the outer sheath

of the cable is held

firmly by the clamp

Fit a 5 amp fuse

Connect

brown to

L (live)

230 volts AC

only. Never use

a light socket

• Before replacing the top cover of the plug ensure

that the cable restraint is holding the outer sheath of

Fit a 13 amp fuse

CD600 Circ saw ML p01-41 07/01/2000, 3:43 pm25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ks 855 n Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker ks 855 n

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info