Bedienungsanleitung Black Decker ks 890 gdtbd scorpion (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

382702

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-off button

3. Blade release button

Fig. A

4. Large capacity blade

5. Curve cutting blade

6. Metal cutting blade

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingandremovingasawblade(g.B&C)

Fitting

u Place the blade over the location pin (7).

u Rotate the blade upward through 90° until it is fully located

in the saw blade slot (8) and the location pin is in the

locked position.

u Make sure the blade is securely tted by trying to remove

it without depressing the blade release button (3).

If you are unable to t the blade, check if the location pin is in

the correct position as shown in g. C. If it is not, keep the

blade release button depressed and use a screwdriver to turn

the location pin into the correct position.

Removing

u Keep the blade release button (3) depressed and rotate

the blade downward through 90°.

u Take the blade sideways off the location pin and slide it

out of the tool.

u Release the blade release button.

Use

Warning! Let the tool work at its own pace. Do not overload.

Switchingonandoff(g.D)

u To switch the tool on, push the two lock-off buttons (2) into

the unlock position and press the variable speed switch (1).

u To switch the tool off, release the variable speed switch.

Sawing(g.E)

u If possible, always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u Use the same back and forth movement you would

employ with a normal hand saw. This enables a quicker

and cleaner cut.

Hints for optimum use

Sawing wood

u Clamp the workpiece securely and remove all nails and

metal objects.

u When splintering is to be minimised, e.g. when cutting

laminates, clamp a piece of scrap wood or hardboard to

both sides of the workpiece and saw through this sandwich.

Sawing metal

u Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal. Use a ne-

tooth saw blade for ferrous metals and a coarser saw

blade for nonferrous metals.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Cutting branches

u Cut downward and away from your body.

u Make the cut close to the main branch or tree body.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ks 890 gdtbd scorpion Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info