Bedienungsanleitung Black Decker KS1000E T1 (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

580867

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

Connecting a vacuum cleaner to the tool (fig. C & D)

X Attach the dust extraction adaptor (9) to the shoe plate (8)

as shown.

X Connect the vacuum cleaner hose (not supplied) to the

adaptor.

Use

Warning! Never use the tool when the shoe plate is loose or

removed.

Adjusting the shoe plate for bevel cuts (fig. E)

The shoe plate can be set to a left or right bevel angle of up

to 45°.

X Turn the shoe plate locking knob (7) counter-clockwise to

release the shoe plate (8).

X Pull the shoe plate (8) backwards and set it to the required

angle. You can use a protractor to check the angle.

X Turn the locking knob (7) clockwise to lock the shoe plate in

place.

To reset the shoe plate for straight cuts:

X Turn the locking knob (7) counter-clockwise to release the

shoe plate (8).

X Set the shoe plate (8) to an angle of approx. 0° then push it

forward.

X Turn the locking knob (7) clockwise to lock the shoe plate in

place. Make sure that the shoe plate is supported by the

guide ribs.

Variable speed control

X Set the variable speed control knob (1) to the required

speed range. Use a high speed for wood, medium speed for

aluminium and PVC and low speed for metals other than

aluminium.

Turbo selector

X For accurate straight and curve cutting and a smooth

surface finish, set the turbo selector (6) to position 0.

X For fast and efficient straight cuts in wood, set the turbo

selector (6) to position 2.

Switching on and off

X To switch the tool on, press the on/off switch (3).

X To switch the tool off, release the on/off switch (3).

X For continuous operation, press the lock-on button (2) and

release the on/off switch.

X To switch the tool off when in continuous operation, press

the on/off switch (3) once more and release it.

Operating the laser (fig. F - I)

(Not supplied with the KS1000NL)

Installing the batteries (fig. F)

Detach the laser module (13) from the jigsaw by removing

the screw (15) and pulling the laser module forward. Insert

two new 1.5 Volt AAA alkaline batteries, making sure to

match the (+) and (-) terminals correctly. Re-attach the laser

module (13).

Adjusting the laser side-to-side (fig. G)

Note: The laser is intended as a cutting aid and does not

guarantee a precise cut.

Warning! Do not adjust the laser with the jigsaw plugged in.

X Use the laser adjustment screw (16) to align the laser line

with the saw blade if needed.

The laser visibility (power) will be reduced if the jigsaw is

overheated. The laser may not be visible when the saw is

overloaded for a prolonged period of time. The laser visibility

will gradually return to normal when the tool cools down

even when the tool is unplugged.

Warning! Do not leave the overheated laser switched ON.

Make sure that the switch is in the OFF position and remove the

batteries to cut power to the laser.

Using the laser (fig. H & I)

The laser projects the line of cut on to the surface of the

workpiece.

X To switch the laser on, press the button (17).

X To switch the laser off, press the button (17) again.

Viewing from directly above the jigsaw, the line of cut can be

easily followed. Should this view be restricted for any

reason, the laser can be used as an alternative cutting guide.

X Use a pencil to mark the cutting line.

X Position the jigsaw over the line.

X Switch on the laser.

Hints for optimum use

Sawing laminates

Because the saw blade cuts on the upward stroke,

splintering may occur on the surface closest to the shoe

plate.

X Use a fine-tooth saw blade.

X Saw from the back surface of the workpiece.

X To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich.

Sawing metal

X Be aware that sawing metal takes much more time than

sawing wood.

X Use a saw blade suitable for sawing metal.

X When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS1000E T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS1000E T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info