Bedienungsanleitung Black Decker KS1400L T2 (Seite 9 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

579739

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

u The height difference between the toothed rim and the

lower end of the riving knife should be 2 - 3 mm.

u Tighten the screws.

Fittingandremovingtheparallelfence(g.C)

u The parallel fence is used to saw in a straight line parellel

to the edge of the workpiece.

Fitting

u Loosen the locking knob (18).

u Insert the parallel fence (19) through the openings (20).

u Slide the parallel fence into the desired position.

u Tighten the locking knob.

Removing

u Loosen the locking knob.

u Pull the parallel fence off the tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

This tool can be used in the right hand or the left hand.

Adjustingthesawingangle(g.D)

The default angle between the saw blade and the shoe is 90°.

u Use a square to check that the angle between the saw

blade and the shoe is 90°. If the angle does not measure

90° adjust as follows:

u Loosen the locking knob (21) to unlock the saw shoe.

u Loosen the locknut (22) on the adjusting screw (23).

u Screw the adjusting screw in or out to achieve a 90° angle.

u Retighten the locknut.

u Tighten the locking knob to lock the saw shoe in place.

Adjustingthedepthofcut(g.E)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx.

2 mm.

u Loosen the knob (24) to unlock the saw shoe.

u Move the saw shoe (8) into the desired position.

The corresponding depth of cut can be read from the

scale (25).

u Tighten the knob to lock the saw shoe in place.

Adjustingthebevelangle(g.F)

This tool can be set to bevel angles between 0° and 45°.

u Loosen the locking knob (21) to unlock the saw shoe.

u Move the saw shoe (10) into the desired position.

The corresponding bevel angle can be read from the

scale (26).

u Tighten the locking knob to lock the saw shoe in place.

Switching on and off

u To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

u To switch the tool off, release the on/off switch.

Sawing

Always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u Work with the shoe pressed against the workpiece.

Hints for optimum use

u As some splintering along the line of cut on the top side of

the workpiece cannot be avoided, cut on the side where

splintering is acceptable.

u Where splintering is to be minimised, e.g. when cutting

laminates, clamp a piece of plywood onto the top of the

workpiece.

Usingthesightguide(g.G)

The tool is equipped with a sight guide for straight cutting (27)

and for 45° bevel cutting (28).

u Adjust the sight guide as described below.

u Align the left edge of the guides (27) or (28) with the

cutting line (29).

u Keep the sight guide aligned with the cutting line while

sawing.

u Work with the shoe pressed against the workpiece.

Adjusting the sight guide

u Make a test cut halfway through a piece of scrap wood.

u Withdraw the saw so the cutting line (29) becomes visible.

u While keeping the saw in this position, loosen the sight

guide on the saw shoe as shown.

u Align the 0° mark (27) on the sight guide with the cutting

line (29). When adjusting for 45° bevel cuts, align the 45°

mark (28) on the sight guide with the cutting line.

u Secure the sight guide using the screw (30).

Howtousethelaser(g.H)

The laser projects the line of cut on the workpiece surface.

u To switch the laser on, slide the switch (6) forward.

u To switch the laser off, slide the switch (6) backward.

Viewing from directly above the saw, the line of cut can be

easily followed. Should this view be restricted for any

reason, the laser can be used as an alternate cutting

guide.

u Use a pencil to mark the cutting line.

u Position the saw over the line.

u Switch on the laser.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS1400L T2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS1400L T2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info