Bedienungsanleitung Black Decker KS1600L T1 (Seite 8 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

579745

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Additional safety instructions for lasers

Read all of this manual carefully.

This product is not to be used by children under 16.

Warning! Laser radiation.

Do not look into the laser beam.

Do not view the laser beam directly with optical

instruments.

per IEC60825-1:2001

Pmax < 2.2mW 630-675nm

Refer to the laser product characteristics.

u This laser complies with class 2 according to

IEC60825-1:2007. Do not replace a laser diode with a

different type. If damaged, have the laser repaired by an

authorised repair agent.

u Do not use the laser for any purpose other than projecting

laser lines.

u An exposure of the eye to the beam of a class 2 laser is

considered safe for a maximum of 0.25 seconds.

Eyelid reflexes will normally provide adequate protection.

At distances over 1 m, the laser complies with class 1 and

thus is considered completely safe.

u Never look into the laser beam directly and intentionally.

u Do not use optical tools to view the laser beam.

u Do not set up the tool at a position where the laser beam

can cross any person at head height.

u Do not let children come near the laser.

Warning! The use of controls or adjustment or performance of

procedures other than those specied in these instructions

may result in exposure to hazardous laser radiation.

Warning! This tool is intended for indoor use only. Do not use

the tool for outdoor applications.

Features

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Spindle lock button

6. Laser on/off switch

7. Laser aperture

8. Shoe

9. Saw blade

10. Saw blade guard

11. Riving knife

12. Saw dust outlet

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Removingandttingasawblade(g.A)

Removing

u Keep the spindle lock button (5) depressed and rotate the

blade until the spindle lock engages.

u Loosen and remove the blade retaining screw (13) by

turning it counterclockwise using the spanner (14)

supplied.

u Remove the outer washer (15).

u Remove the saw blade (9).

Fitting

u Place the saw blade onto the inner flange (16), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

u Fit the outer washer (15) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (13) into the hole.

u Keep the spindle lock button (5) depressed.

u Securely tighten the blade retaining screw by turning it

clockwise using the spanner (14) supplied.

u Adjust the riving knife as described below.

Adjustingtherivingknife(g.B)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

u Loosen the screws (17), using the spanner (14), while

holding the riving knife in position.

u Position the riving knife (11) as shown.

u The distance between the toothed rim and the riving knife

should be 2 - 3 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS1600L T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS1600L T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info