Bedienungsanleitung Black Decker KS1880S T1 (Seite 5 von 8) (Englisch)

581143

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Assembly

Fitting and removing the battery (fig. A)

◆ To fit the battery (6), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

◆ To remove the battery, push the release button (7) while

at the same time pulling the battery out of the receptacle.

Fitting the saw blade (fig. B)

◆ Hold the saw blade securely. If the saw blade is fitted

with a tooth protector, leave it attached while fitting the

blade.

◆ Pull the blade clamp lever (5) up to release the blade

clamping mechanism.

◆ Insert the shank of the saw blade into the blade holder (3)

as far as it will go.

◆ Move the blade clamp lever (5) down to lock the blade

clamping mechanism.

◆ Remove the tooth protector, if fitted.

Note: This tool has been designed to allow the saw blades to

be fitted with the teeth facing forward or backward.

Use

Charging the battery (fig. A)

The battery needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery for the

first time, or after prolonged storage, it will only accept an

80% charge. After several charge and discharge cycles, the

battery will attain full capacity. The battery may become warm

while charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery (6), remove it from the tool.

◆ Slide the charger receptacle (9) onto the battery as shown.

◆ Plug in the charger (8). Switch on at the mains.

The battery will become warm while charging. After approx.

3 hours of charging, the battery will be sufficiently charged for

use in regular applications. After approx. 6 hours of charging,

the battery will be fully charged.

◆ Remove the charger receptacle from the battery.

Switching on and off

◆ To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

◆ To switch the tool off, release the on/off switch.

Sawing (fig. C)

◆ Always hold the tool with both hands.

◆ Let the blade run freely for a few seconds before starting

the cut.

◆ Apply only a gentle pressure to the tool while performing

the cut.

◆ If possible, work with the shoe pressed against the

workpiece. This will improve tool control and reduce tool

vibration, as well as prevent the blade from being

damaged.

Hints for optimum use

Sawing wood

◆ Clamp the workpiece securely and remove all nails and

metal objects.

◆ Holding the tool with both hands, work with the shoe

pressed against the workpiece.

Pocket cutting in wood

◆ Measure and mark the required pocket cut.

◆ Fit a saw blade suitable for pocket cutting.

◆ Rest the shoe on the workpiece in such a position that the

blade forms an appropriate angle for the pocket cut.

◆ Switch on the tool and slowly feed the blade into the

workpiece. Make sure that the shoe remains in contact

with the workpiece at all times.

Sawing metal

◆ Be aware that sawing metal takes much more time than

sawing wood.

◆ Use a saw blade suitable for sawing metal.

Use a fine-tooth saw blade for ferrous metals and a

coarser saw blade for nonferrous metals.

◆ When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut

through this sandwich.

◆ Spread a film of oil along the intended line of cut.

Cutting branches

Branches up to 25 mm in diameter can be cut with this tool.

Warning! Do not use the tool while in a tree, on a ladder or

on any other unstable surface. Be aware of where the branch

will fall.

◆ Cut downward and away from your body.

◆ Make the cut close to the main branch or tree body.

Vertical cutting

The tool allows close cutting to corners and other difficult

areas.

◆ Insert the shank of the saw blade into the blade holder

with the teeth of the blade facing upward.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS1880S T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS1880S T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info