Bedienungsanleitung Black Decker KS40 T1 (Seite 8 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

579747

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

1. On/off switch

2. Lock-off button

3. Main handle

4. Side handle

5. Depth of cut adjustment lever

6. Depth of cut scale

7. Locking knob for mitre angle adjustment

8. Mitre angle scale

9. Saw blade guard

10. Retracting lever for saw blade guard

11. Saw shoe

12. Parallel fence

13. Riving knife

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Removingandttingasawblade(g.A)

Removing

u Insert a screwdriver into the hole (14) to prevent the saw

blade from rotating. Alternatively, hold the outer washer

(15) using an 18 mm spanner.

u Loosen and remove the blade retaining screw (16) by turning

it counterclockwise using the Allen key (17) supplied.

u Remove the outer washer (15).

u Remove the saw blade (18).

Fitting

u Place the saw blade onto the inner washer (19), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

u Fit the outer washer (15) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (16) into the hole.

u Insert a screwdriver into the hole (14) to prevent the saw

blade from rotating. Alternatively, hold the outer washer (15)

using an 18 mm spanner.

u Securely tighten the blade retaining screw by turning it

clockwise using the Allen key (17) supplied.

u Adjust the riving knife as described below.

Adjustingtherivingknife(g.B)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

u Loosen the screw (20).

u Position the riving knife (13) as shown.

- The distance between the toothed rim and the riving

knife should be 2 - 3 mm.

- The height difference between the toothed rim and the

lower end of the riving knife should be 2 - 3 mm.

u Tighten the screw (20).

Fittingandremovingtheparallelfence(g.E)

The parallel fence is used to saw in a straight line parallel to

the edge of the workpiece.

Fitting

u Loosen the locking knob (21).

u Insert the parallel fence (12) through the openings (22).

u Slide the parallel fence into the desired position.

u Tighten the locking knob.

Removing

u Loosen the locking knob (21).

u Pull the parallel fence off the tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

This tool can be used in the right hand or the left hand.

Warning! Carefully guide the cable in order to avoid

accidentally cutting it.

Adjustingthedepthofcut(g.D)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx. 2 mm.

u Loosen the knob (5) to unlock the saw shoe.

u Move the saw shoe (11) into the desired position. The

corresponding depth of cut can be read from the scale (6).

u Tighten the knob to lock the saw shoe in place.

Adjustingthemitreangle(g.E)

This tool can be set to mitre angles between 0° and 45°.

u Loosen the locking knob (7) to unlock the saw shoe.

u Move the saw shoe (11) into the desired position. The

corresponding mitre angle can be read from the scale (8).

u Tighten the locking knob to lock the saw shoe in place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS40 T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS40 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info