Bedienungsanleitung Black Decker ks632 (Seite 24 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

445768

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH

All models

Note: To achieve a greater accuracy of cut, ensure

back of blade is touching blade support roller. See

‘Blade suport roller’ for instructions on how to change

position of blade support roller.

BLADE SUPPORT ROLLER

To provide greater support and accuracy when cutting,

your jigsaw is fitted with a blade support roller. This

support should be adjusted so that the roller touches

the back of the blade when cutting.

To do this, loosen the front

screw on the base of the

shoe. Push the blade

support forward until the

roller touches the back

edge of the blade. Retighten

the screw. Lubricating the

guide roller (5) from time to time with a drop of oil will

extend the life of the roller.

For scroller jigsaws only

Note: When using your jigsaw in the scrolling mode,

the blade support roller needs to be retracted to allow

free movement of the blade.

To do this, untighten the

front screw on the base of

the shoe and retract the

support. Re-tighten the

screw.

OPERATING YOUR JIGSAW

To switch your jigsaw on, fully squeeze the on/off

trigger switch (1). To switch your jigsaw off, release

the trigger switch (1). When plugging your jigsaw in,

ensure the trigger switch is in the OFF position.

When continuous operation is required, squeeze the

trigger and depress the lock on button (2) and release

the trigger. To disengage the lock, squeeze and release

the trigger. Always disengage the lock before

disconnecting from the power supply.

SAW SHOE ADJUSTMENT FOR ANGULAR CUTTING

The shoe plate (6) can be angled up to 45˚ on either side.

To do this, disconnect your jigsaw from the power supply.

Raise or remove the dust

shroud (4) and loosen both

screws on the shoe plate

with a screwdriver. Pull the

shoe plate backward a little,

and set the desired angular

adjustment according to the

scale or push the shoe plate

forward for fixed locks at 0˚,

15˚, 30˚, or 45˚. Tighten the

screws to secure. Although

the scale and notches are

accurate for most purposes

it is advisable for very

accurate angle cutting to use a protractor to set the

shoe. Make a test cut on some scrap material to check

the accuracy of the angle. To reset the shoe for a

square cut, slacken the clamp screws and move the

shoe until it is approximately 90˚ to the blade, and then,

whilst applying slight forward pressure on the shoe,

retighten the clamp screws. If necessary, re-adjust the

blade support roller using only the front screw.

DUST BLOWING

To aid visibility when cutting,

your jigsaw is fitted with a

facility which will blow dust

away from surface of

material being cut. To utilise,

lift up or remove dust visor

and ensure the variable

blower control is pointing towards the symbol.

DUST EXTRACTION

Your jigsaw with a hose adapter (accessory part), can

be fitted to most portable vacuum cleaners.

To utilise this facility push

adapter into the aperture at

the rear of jigsaw and fit

vacuum hose in or over the

adapter, depending on the

hose size. The dust shroud

should be attached and in a

downwards position and

the variable blower control

on the side of the jigsaw

should point towards the

symbol.

ELECTRONIC SPEED REGULATION

For electronic models only

The electronic speed

control wheel (3) is used to

programme the required

saw speed depending on

the material being worked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ks632 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info