Bedienungsanleitung Black Decker KS633E T4 (Seite 25 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

580931

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

The correct speed for a particular material can be

obtained from the following table:

Material Electronic speed regulation

Wood 6 - max

Metal 2 - 3

Aluminium 3 - 5

PVC 3 - 4

Ceramic 3 - 5

Note: After using your jigsaw for extended periods on

stroke settings 1-4, run the saw for 3 minutes at

maximum speed to aid cooling.

SCROLLING

For scroller jigsaws only

Before use, remember to retract the blade support

roller and ensure the shoe is in the forward position.

The scrolling feature enables you to have maximum

control whilst following complex cut lines.

To operate, press the button

(10) on the front of your

jigsaw and the scroller knob

(9) will spring upwards. Pull

the knob up to its full extent.

Your jigsaw is now ready for

scrolling mode. Using one

hand to guide the jigsaw,

turn the scroller knob to guide the blade along the line

of cut. The blade will turn a full 360˚.

The orientation of the blade

can be locked in any one of

4 positions - 0˚, 90˚, 180˚,

270˚ to enable straight

cutting in awkward areas.

To lock the blade in any of

these four positions, push

the button in on the front of the unit, and push the knob

down. When the button is released the blade is locked

in position. To reset, push the button on the front of the

jigsaw. For straight line cutting, press the button on the

front of your jigsaw and push the knob down and

replace the blade support roller to touch the back of

the blade.

HANDY HINTS

Cutting laminates

The blades of your jigsaw cut on the upstroke so any

tendency for edge splintering will occur on the face of

the material nearest the saw shoe. When sawing thin

wood or plastic laminates, use a fine tooth metal

cutting blade and cut from the back surface of the

270˚ 180˚

0˚ 90˚

material. To minimise the risk of chipping the edges of

plastic laminate, clamp a piece of scrap wood

or hardboard to both sides of the laminate to form a

sandwich, and saw through the complete assembly.

Always select the right blade for the job.

Pocket cutting

The saw blade can be inserted directly into a wood

surface without first drilling a pilot hole, thus

eliminating a drilling operation.

First measure and clearly mark the surface to be cut.

Then tip your jigsaw forward so that the rounded tips of

the shoe rest on the work surface but with the blade

well clear of it. Switch your jigsaw on and move the

saw down until the moving blade is exactly over the

chosen point of entry. Lower the rear of the shoe down

towards the work slowly, maintaining a firm pivoting

pressure on the shoe tips with the blade exactly on the

required line. Do not move your jigsaw forward along

the cut line until the saw blade has completely

entered the material and the shoe comes to rest flat

on its surface.

Cutting metal

Your jigsaw can be used for cutting light gauge ferrous

sheet and non-ferrous metals such as copper, brass,

aluminium, etc.

It is advisable when cutting thin sheet to clamp a

backing sheet of soft wood or plywood to the work as

this will enable you to obtain a clean cut without

vibration and the possibility of tearing the metal. Both

metal and wood backing are sawn together. Do not

force the cutting blade into the metal as this will

reduce the life of the blade and possibly damage the

motor. Cutting thin metal will take longer than cutting

even a relatively thick piece of wood, so do not be

tempted to speed up the operation by forcing the saw.

Spread a thin film of oil along the proposed cutting line

before commencing to saw metal. Always select the

right blade for the job.

Cleaning

Disconnect your jigsaw from the power supply. Use

only mild soap and a slightly damp cloth to clean your

jigsaw. Many household cleaners contain chemicals

which could seriously damage the plastic. Also, do not

use petrol, turpentine, lacquer or paint thinners or

similar products. Never let any liquid get inside the tool

and never immerse any part of your jigsaw into liquid.

EC DECLARATION OF CONFORMITY

We declare that units: KS638SE, KS635S, KS634S,

KS633E, KS632E, KS631, KS630, KS629 conform to

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS633E T4 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS633E T4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info