Bedienungsanleitung Black Decker KS800EL T1 (Seite 8 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

580993

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and

that the saw blade has stopped. Used saw blades may be

hot.

Fitting the saw blade (fig. B)

X Hold the saw blade (10) as shown, with the teeth facing

forward.

X Push and hold the blade clamp (9) down.

X Insert the shank of the saw blade into the blade holder

(11) as far as it will go.

X Release the blade clamp (9).

Saw blade storage (fig. C)

Saw blades (10) can be stored in the storage compartment

located on the side of the tool.

X Open the cover (3) of the saw blade storage

compartment by holding the tab on the top of the cover

(3) and pulling it outward.

X The blades are retained in the compartment by a

magnetic strip. To remove a blade, press down on one

end of the blade to raise the other end, and remove.

X Close the cover (3) of the saw blade storage

compartment and make sure that it is latched closed.

Warning! Close the compartment door securely before

operating the saw.

Connecting a vacuum cleaner to the tool (fig. D)

An adaptor is required to connect a vacuum cleaner or dust

extractor to the tool. The dust extraction adaptor (6) can be

purchased from your local Black & Decker retailer.

X Push the adaptor (6) into the dust extraction outlet (5).

X Connect the vacuum cleaner hose to the adaptor (6).

Use

Adjusting the shoe plate for bevel cuts (fig. E and F)

Warning! Never use the tool when the shoe plate is loose or

removed.

The shoe plate (7) can be set to a left or right bevel angle of

up to 45°.

X Pull the shoe plate locking lever (4) outwards to unlock

the shoe plate (7) from the 0 degree position (fig. F).

X Pull the shoe plate (7) forward and set the required

bevel 15°, 30° and 45° indicated in the bevel angle

window.

X Push the shoe plate locking lever (4) back towards the

saw to lock the shoe plate (7).

To reset the shoe plate (7) for straight cuts:

X Pull the shoe plate locking lever (4) outwards to unlock

the shoe plate (7).

X Set the shoe plate (7) to an angle of 0° and push the

shoe plate backwards.

X Push the shoe plate locking lever (4) back towards the

saw to lock the shoe plate (7).

Switching on and off

X To switch the tool on, press the variable speed on/off

switch (2).

X To switch the tool off, release the variable speed on/off

switch (2).

X For continuous operation, press the lock-on button (1)

and release the on/off switch (2).

X To switch the tool off when in continuous operation,

press the on/off switch (2) and release it.

Sawing

Hold the tool firmly with both hands while cutting.

The shoe plate (7) should be held firmly against the material

being cut. This will help prevent the saw from jumping,

reduce vibration and minimise blade breakage.

X Let the blade run freely for a few seconds before starting

the cut.

X Apply only a gentle pressure to the tool while performing

the cut.

Operating the laser (fig. G - I) (‘L’ units only)

Installing the batteries (fig. G)

Detach the laser module (13) from the jigsaw by removing

the screw (12) and pulling the laser module forward. Insert

two new 1.5 Volt AAA alkaline batteries, making sure to

match the (+) and (-) terminals correctly. Re-attach the laser

module (13).

Adjusting the laser side-to-side (fig. H)

Note: The laser is intended as a cutting aid and does not

guarantee a precise cut.

Warning! Do not adjust the laser with the jigsaw plugged in.

X Use the laser adjustment screw (14) to align the laser

line with the saw blade if needed.

The laser visibility (power) will be reduced if the jigsaw is

overheated. The laser may not be visible when the saw is

overloaded for a prolonged period of time. The laser visibility

will gradually return to normal when the tool cools down even

when the tool is unplugged.

Warning! Do not leave the overheated laser switched ON.

Make sure that the switch is in the OFF position and remove

the batteries to remove power from the laser.

Using the laser (fig. I and J)

The laser projects the line of cut (17) on to the surface of the

workpiece.

X To switch the laser on, press the button (15).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS800EL T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS800EL T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info