Bedienungsanleitung Black Decker KS800ELW T1 (Seite 6 von 16) (Englisch)

580997

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will make sure that the safety of the power tool is

maintained.

Additional power tool safety warnings

XHold the tool by the insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a "live" wire will make exposed metal parts

of the tool "live" and shock the operator.

XUse clamps or another practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body leaves it unstable

and may lead to loss of control.

XKeep hands away from cutting area. Never reach

underneath the work piece any reason. Do not insert

fingers or thumb into the vicinity of the reciprocating

blade and blade clamp. Do not stabilize the saw by

gripping the shoe.

XKeep blades sharp. Dull or damaged blades may

cause the saw to swerve or stall under pressure. Always

use the appropriate type of saw blade for the workpiece

material and type of cut.

XWhen cutting pipe or conduit, make sure that they

are free from water, electrical wiring, etc.

XDo not touch the workpiece or the blade

immediately after operating the tool. They can

become very hot.

XBe aware of hidden hazards, before cutting into

walls, floors or ceilings, check for the location of

wiring and pipes.

XThe blade will continue to move after releasing the

switch. Always switch the tool off and wait for the saw

blade to come to a complete standstill before putting the

tool down.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specifically

designed for protection against dust and fumes and ensure

that persons within or entering the work area are also

protected.

XThoroughly remove all dust after sanding.

XTake special care when sanding paint which is possibly

lead based or when sanding some woods and metal

which may produce toxic dust:

- Do not let children or pregnant women enter the work

area.

- Do not eat, drink or smoke in the work area.

- Dispose of dust particles and any other debris safely.

XThis tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

XThe intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those

recommended in this instruction manual may present a

risk of personal injury and/or damage to property

Vibration

The declared vibration emission values stated in the

technical data and the declaration of conformity have been

measured in accordance with a standard test method

provided by EN 60745 and may be used for comparing one

tool with another. The declared vibration emission value may

also be used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

Warning! Additional safety warnings for jigsaws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS800ELW T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS800ELW T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info