Bedienungsanleitung Black Decker KS800SW T1 (Seite 10 von 16) (Englisch)

581010

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

How to use the Auto SelectTM dial (fig. G)

This tool is fitted with a unique Auto SelectTM Dial (8) to set the speed and the pendulum blade action for various cutting

applications. To select the optimum speed and pendulum blade action for the type of material being cut, turn the dial (8) as

shown in the table below:

Switching on and off

To switch the tool on, press the on/off switch (2).

To switch the tool off, release the on/off switch (2).

For continuous operation, press the lock-on button (1)

and release the on/off switch (2).

To switch the tool off when in continuous operation,

press the on/off switch (2) and release it.

Sawing

Hold the tool firmly with both hands while cutting.

The shoe plate (7) should be held firmly against the material

being cut. This will help prevent the saw from jumping,

reduce vibration and minimise blade breakage.

Let the blade run freely for a few seconds before starting

the cut.

Apply only a gentle pressure to the tool while performing

the cut.

Operating the laser (fig. H - K) (‘L’ units only)

Installing the batteries (fig. H)

Detach the laser module (14) from the jigsaw by removing

the screw (13) and pulling the laser module forward. Insert

two new 1.5 Volt AAA alkaline batteries, making sure to

match the (+) and (-) terminals correctly. Re-attach the laser

module (14).

Adjusting the laser side-to-side (fig. I)

Note: The laser is intended as a cutting aid and does not

guarantee a precise cut.

Warning! Do not adjust the laser with the jigsaw plugged in.

Use the laser adjustment screw (15) to align the laser line

with the saw blade if needed.

The laser visibility (power) will be reduced if the jigsaw is

overheated. The laser may not be visible when the saw is

overloaded for a prolonged period of time. The laser visibility

will gradually return to normal when the tool cools down even

when the tool is unplugged.

Warning! Do not leave the overheated laser switched ON.

Make sure that the switch is in the OFF position and remove the

batteries to remove power from the laser.

Using the laser (fig. J and K)

The laser projects the line of cut (18) on to the surface of the

workpiece.

To switch the laser on, press the button (16).

To switch the laser off, press the button (16) again.

Icon Application Speed Blade Type

Kitchen work surfaces,

work tops, laminate

board

Fast speed General wood

Scrolling/curves/

craftwork, hardwoods,

decking, flooring

Fast speed Scrolling wood

General wood

Plywood and wood

panels

Fast speed General wood

General timber, soft

wood, fast rip cutting

Fast speed General wood

Plastics, Perspex, PVC Medium speed General purpose

Sheet metal tin plate,

ceramic tile, fibreglass

sheet

Low speed Metal or ceramic or

fibreglass blade

Slow speed, precision

start

Slow speed Choose the correct

blade for the

application

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS800SW T1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS800SW T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info