Bedienungsanleitung Black Decker KS901PEK (Seite 8 von 12) (Englisch)

581121

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

u Use a ne-tooth saw blade.

u Saw from the back surface of the workpiece.

u To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich. Alternatively, t the anti-splinter guard (13)

that is supplied with your product. (KS901SE only).

Sawing metal

Warning! Do not use a vacuum when cutting metal. Metal

lings will be hot and may cause re.

Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Rip Fence

Ripping and circle cutting without a pencil line are easily done

with a rip fence and circle guide (available as an optional extra

- part number X43005-XJ).

Attaching Rip Fence (gs. H & I)

u Insert rip fence (14) into the shoe plate slots with the cross

bar facing down as shown in gure H.

u Place screw (15) into hole in bottom of shoe plate.

u Align clamp bar (16) over screw with lipped edge facing

down and pointing towards the rear of the saw.

u Using a phillips screwdriver, run the screw into the

threaded hole in the bar clamp as shown in gure I.

u Adjust to width of cut and tighten screw.

Circle Cutting (g. J)

u Insert rip fence into slot on the right side of shoe plate with

cross bar facing up.

u Adjust rip fence so that distance from blade to hole in

cross bar is the desired radius and tighten screw.

u Place saw so that centre of hole in cross bar is over centre

of circle to be cut (make plunge cut, drill hole for blade or

cut inward from edge of material to get blade into posi-

tion).

u When saw is properly positioned, drive a small nail

through hole in cross bar into exact centre of circle to be

cut.

u Using rip fence as a pivot arm, begin cutting circle.

Plunge Cutting (g. K)

A plunge cut is an easy method of making an inside cut. The

saw can be inserted directly into a panel or board without rst

drilling a lead or pilot hole. In plunge cutting, measure the sur-

face to be cut and mark clearly with a pencil. Next tip the saw

forward until the front end of the shoe sits rmly on the work

surface and the blade clears the work through its full stroke.

Switch the tool on and allow it to attain maximum speed. Grip

the saw rmly and lower the back edge of tool slowly until the

blade reaches its complete depth. Hold the shoe at against

the wood and begin cutting. Do not remove blade from cut

while it is still moving. Blade must come to a complete stop.

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

u Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Never let any liquid get inside the tool and never immerse

any part of the tool into liquid.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your BLACK+DECKER product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

Separate collection of used products and packag-

ing allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or

by the retailer when you purchase a new product.

BLACK+DECKER provides a facility for the collection and re-

cycling of BLACK+DECKER products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS901PEK Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS901PEK

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info