Bedienungsanleitung Black Decker KS950SW T1 (Seite 6 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581127

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will make sure that the safety of the power tool is

maintained.

Specific safety instructions for jigsaws

X Hold the tool by the insulated gripping surfaces when

performing an operation where the cutting tool may contact

hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the

operator.

X Use clamps or another practical way to secure and support

the workpiece to a stable platform. Holding the work by

hand or against your body leaves it unstable and may lead

to loss of control.

X Keep hands away from cutting area. Never reach

underneath the work piece any reason. Do not insert

fingers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

X Keep blades sharp. Dull or damaged blades may cause the

saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

X When cutting pipe or conduit, make sure that they are free

from water, electrical wiring, etc.

X Do not touch the workpiece or the blade immediately after

operating the tool. They can become very hot.

X Be aware of hidden hazards, before cutting into walls,

floors or ceilings, check for the location of wiring and pipes.

X The blade will continue to move after releasing the switch.

Always switch the tool off and wait for the saw blade to

come to a complete standstill before putting the tool down.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specifically

designed for protection against dust and fumes and ensure

that persons within or entering the work area are also

protected.

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

X This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

X If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Additional safety instructions for non-rechargeable

batteries

X Never attempt to open for any reason.

X Do not store in locations where the temperature may

exceed 40 °C.

X When disposing of batteries, follow the instructions given in

the section "Protecting the environment".

Do not incinerate the batteries.

X Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries, proceed as follows:

- Carefully wipe the liquid off using a cloth. Avoid skin

contact.

Additional safety instructions for lasers

X This laser complies with class 2 according to IEC

60825+A1+A2:2001. Do not replace a laser diode with a

different type. If the laser is damaged, have the laser

repaired by an authorised repair agent.

X Do not use the laser for any purpose other than projecting

laser lines.

Read all of this manual carefully.

This product is not to be used by

children under 16.

Laser radiation.

Do not look into the laser beam.

Do not use optical tools to view the

laser beam.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS950SW T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS950SW T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info