Bedienungsanleitung Black Decker KS990EK T1 (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581128

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

◆ Fit the edge guide shoe (17) in the same way as the

normal shoe.

Note 1: The cross bar (18) can be fitted in two ways:

◆ Fit the cross bar with the sides up for circle cutting.

◆ Fit the cross bar with the sides down for ripping.

Note 2: The guide arm (19) can be mounted on either side of

the shoe (fig. E).

◆ Remove the screw (20).

◆ Rotate the guide arm 180° and refit it on the other side of

the shoe.

◆ Secure the guide arm with the screw, using the other hole

(21).

Use

Setting the cutting speed (fig. F)

◆ Set the speed control wheel (3) to the required speed

range (1 = low speed, 6 = high speed).

◆ Use a high speed for wood, a medium speed for

aluminium, ceramics and PVC and a low speed for metals

other than aluminium.

Note: After using the saw for extended periods on low speeds,

run the saw on high speed for 3 minutes to aid cooling.

Switching on and off (fig. G)

◆ To switch the tool on, press the lock-off button (2) and

squeeze the on/off switch (1).

◆ To switch the tool off, release the on/off switch.

Cutting circles (fig. D & H)

The circle guide can be used to saw out circular patterns.

◆ Fit the circle guide for circle cutting.

◆ The guide arm (19) is marked to allow you to set the cross

bar (18) to the radius of the circle to be cut.

◆ Loosen the knob (22) and slide the cross bar over the

guide arm to the desired position.

◆ Tighten the knob.

◆ Drill a small hole for the point of the pivot knob in the

centre of the circle to be cut.

◆ Drill a second hole where the saw blade will be

positionend or cut inwards from the edge of the

workpiece to get the sawblade into position.

◆ Saw out the circle in a counterclockwise direction. Note:

Left-handed users should saw in a clockwise direction.

Using the edge guide (fig. D & I)

The edge guide can be used to maintain an equal cutting

distance when ripping.

◆ Fit the edge guide for ripping.

◆ Loosen the knob (22) and slide the cross bar (18) over the

guide arm (19) to the desired position.

◆ Tighten the knob.

◆ Keep the cross bar pressed firmly against the straight

edge of the workpiece during sawing.

Hints for optimum use

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may

occur on the surface closest to the shoe plate.

◆ Use a fine-tooth saw blade.

◆ Saw from the back surface of the workpiece.

◆ To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw

through this sandwich.

Sawing metal

◆ Be aware that sawing metal takes much more time than

sawing wood.

◆ Use a saw blade suitable for sawing metal. Use a fine-

tooth saw blade for ferrous metals and a coarser saw

blade for nonferrous metals.

◆ When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut

through this sandwich.

◆ Spread a film of oil along the intended line of cut.

Cutting branches

Branches up to 25 mm in diameter can be cut with this tool.

Warning! Do not use the tool while in a tree, on a ladder or

on any other unstable surface. Be aware of where the branch

will fall.

◆ Cut downward and away from your body.

◆ Make the cut close to the main branch or tree body.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you will

get the very best from your tool.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Protecting the environment

Black & Decker provides a facility for recycling

Black & Decker products once they have reached the

end of their working life. This service is provided

free of charge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS990EK T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info