Bedienungsanleitung Black Decker kw 850 e (Seite 12 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

426955

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

Fitting the centring pin (fig. O)

◆ Fit the edge guide to the router as shown in

fig. C, but upside down.

◆ Fit the centring pin (22) to the workpiece side

of the edge guide with the screw (23) provided.

Fitting the copy follower (fig. P)

◆ Fit the edge guide to the router as shown in

fig. C.

◆ Fit the ‘L’ bar (24) to the upper side of the edge

guide using the two screws and nuts provided.

◆ Fit the rotating attachment (25) to the ‘L’ bar

with the wing screw provided.

USE

Let the tool work at its own pace.

Do not overload.

◆ Carefully guide the cable in order to avoid

accidentally cutting it.

Adjusting the depth of cut (fig. E)

The depth of cut is the distance X between the

depth stop bar (9) and the depth stop (18).

The depth of cut can be set in two different ways

as described below.

Adjusting the depth of cut using a piece of wood

(fig. A & F)

◆ Fit the router bit as described above.

◆ Loosen the locking screw (10).

◆ Pull the plunge lock lever (4) up.

◆ Plunge the router down until the router bit

touches the workpiece.

◆ Push the plunge lock lever (4) down.

◆ Pull the depth stop bar (9) up.

◆ Place a piece of wood with a thickness equal to

the desired depth of cut between the depth

stop (18) and the depth stop bar (9).

◆ Tighten the locking screw (10).

◆ Remove the piece of wood.

◆ Pull the plunge lock lever (4) up and let the

router return to its original position.

◆ After switching the router on, plunge it down

and make the desired cut.

Adjusting the depth of cut using the scale

(fig. A & G)

◆ Fit the router bit as described above.

◆ Loosen the locking screw (10).

◆ Pull the plunge lock lever (4) up.

◆ Plunge the router down until the router bit

touches the workpiece.

◆ Push the plunge lock lever (4) down.

◆ Read the starting position from the scale (11).

◆ Add the desired depth of cut to the starting

position.

◆ Move the depth stop bar (9) to the calculated

position on the scale.

◆ Tighten the locking screw (10).

◆ Pull the plunge lock lever (4) up and let the

router return to its original position.

◆ After switching the router on, plunge it down

and make the desired cut.

Adjusting the revolver depth stop (fig. H)

After turning the revolver depth stop to the desired

setting, you can fine-adjust the depth stop to be used.

If you want to make several cuts with a different

depth of cut, adjust each of the depth stops.

◆ Turn the depth stop screw (19) up or down as

required using a screwdriver.

Setting the speed (fig. A)

◆ Set the speed control knob (3) to the required

speed. Use a high speed for small diameter

router bits. Use a low speed for large diameter

router bits.

Using a batten as a guide (fig. I)

When it is not possible to use the edge guide,

for example when routing grooves in the back

panel of a bookcase to support shelves,

proceed as follows:

◆ Place a batten onto the workpiece.

◆ Move the batten until it is in the correct

position to guide the tool.

◆ Securely clamp the batten to the workpiece.

Using the template guide (fig. M)

The template guide can be used to make a cutout

shape from a template, for instance a letter.

◆ Secure the template over the workpiece with

double-sided tape or ‘G’ clamps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kw 850 e Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info