Bedienungsanleitung Black Decker kw 900 e (Seite 10 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

426956

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

u Pull the plunge lock lever (4) up.

u Plunge the router down until the router bit touches the

workpiece.

u Push the plunge lock lever (4) down.

u Move the pointer (29) in the zero position on the scale (10).

u Add the desired depth of cut to the starting position.

u Move the depth stop bar (9) to the calculated position on

the scale.

u Tighten the locking screw (28).

u Fine adjust using the adjusting knob (30).

u Pull the plunge lock lever (4) up and let the router return to

its original position.

u After switching the router on, plunge it down and make the

desired cut.

Adjustingthedepthofcutusingapieceofwood(g.J)

u Fit the router bit and plunge the router down as described

above.

u Pull the depth stop bar (9) up.

u Place a piece of wood with a thickness equal to the

desired depth of cut between the depth stop (27) and the

depth stop bar (9).

u Tighten the locking screw (28).

u Fine adjust using the adjusting knob (30).

u Remove the piece of wood.

u Pull the plunge lock lever (4) up and let the router return to

its original position.

u After switching the router on, plunge it down and make the

desired cut.

Adjustingtherevolverdepthstop(g.K)

After turning the revolver depth stop to the desired setting, you

can ne-adjust the depth stop to be used. If you want to make

several cuts with a different depth of cut, adjust each of the

depth stops.

u Turn the depth stop screw (31) up or down as required

using a screwdriver.

Setting the speed

u Set the speed control knob (3) to the required speed.

Use a high speed for small diameter router bits. Use a low

speed for large diameter router bits.

Usingabattenasaguide(g.L)

When it is not possible to use the edge guide, for example

when routing grooves in the back panel of a bookcase to

support shelves, proceed as follows:

u Select a piece of wood with a straight edge to use as

a batten.

u Place the batten onto the workpiece.

u Move the batten until it is in the correct position to guide

the tool.

u Securely clamp the batten to the workpiece.

Usingthetemplateguide(g.D)

The template guide can be used to make a cutout shape from

a template, for instance a letter.

u Secure the template over the workpiece with double-sided

tape or ‘G' clamps.

u The router bit must extend below the ange of the

template guide, to cut the workpiece in the shape of the

template.

Usingthedistancepiece(g.E)

The distance piece can be used for trimming wooden or

laminate vertical projections.

Usingthecentringpin(g.F)

The centring pin can be used to cut out circular patterns.

u Drill a hole for the point of the centring pin in the centre of

the circle to be cut.

u Place the router on the workpiece with the point of the

centring pin in the drilled hole.

u Adjust the radius of the circle with the bars of the edge guide.

u The router can now be moved over the workpiece to cut

out the circle.

Usingthecopyfollower(g.G)

The copy follower helps to maintain an equal cutting distance

along the edge of irregularly shaped workpieces.

u Place the router on the workpiece at the desired distance

from the edge to be copied.

u Adjust the bars of the edge guide until the wheel is in

contact with the workpiece.

Switching on and off

Switching on

u Keep the lock-off button (2) depressed and press the on/

off switch (1).

u Release the lock-off button.

Switching off

u Release the on/off switch.

Warning! Always operate the tool with both hands.

Hints for optimum use

u When working on outside edges, move the tool

counterclockwise (g. M). When working on inside edges,

move the tool clockwise.

u Use HSS router bits for softwood.

u Use TCT router bits for hardwood.

u You can use the tool without a guide (g. N). This is useful

for signwriting and creative work. Only make shallow cuts.

u Refer to the table below for common types of router bits.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kw 900 e Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info