Bedienungsanleitung Black Decker KW800 T1 (Seite 27 von 80) (Deutsch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

577910

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

FITTING THE ROUTER BIT

Disconnect the plug from the electricity supply.

If a router bit is

already fitted,

press the spindle

lock button and

release the collet

clamp nut, using

the spanner

provided.

Insert the router

bit. Make sure it

protrudes at least

3mm from the end

of the shank.

Press the spindle

lock button and

tighten the collet

clamp nut using the spanner provided.

ADJUSTING THE DEPTH OF CUT

The depth of cut

is the distance (x)

between the triple

depth stop and

the depth stop bar.

Each router bit

varies in length

and the triple

depth stop

provides three different positions. Use one of the

following methods to set the depth of cut.

USING A PIECE OF WOOD

The most common method is to use a piece of wood as

a gauge as follows:

• Fit the router bit.

• Loosen the wing screw.

• Pull the plunge lock lever up.

• Plunge your router down until the cutter is in contact

with the workpiece.

• Push the plunge lock lever down to hold your

router in this position.

Pull up the depth

stop bar.

Put a piece of

wood of the same

thickness as the

desired depth of

cut, between the

depth stop bar

and the triple

depth stop.

• Tighten the wing screw.

• Remove the piece of wood.

• Pull the plunge lock lever up to move your router

back to its original position.

• Move your router to its working position and set the

on/off switch to ‘I’.

• Plunge your router down to the workpiece and

push the plunge lock lever to hold your router at

this depth.

• Make the desired cut.

USING THE SCALE

Proceed as follows:

• Fit the router bit.

• Loosen the wing screw.

• Pull the plunge lock lever up.

• Plunge your router down until the cutter is in contact

with the workpiece.

• Push the plunge lock lever down to hold your router

in this position. The scale on the depth stop bar now

shows the starting position. This starting position

will vary, depending on the cutter used.

• Add the desired depth of cut to the starting position;

for example, if the scale shows 23mm and the

desired depth of cut is 10mm, the correct adjustment

on the scale is 23 +10 = 33mm. If the scale shows

46mm and the desired depth of cut is 5mm, the

correct adjustment on the scale is 46 + 5 = 51mm.

• Move the depth stop bar to the calculated number.

• Clamp the depth stop bar with the wing screw.

• Pull the plunge lock lever up to move your router to

its original position.

• Move your router to its working position and set the

on/off switch to ‘I’.

• Plunge your router down to the workpiece and

push the plunge lock lever to hold your router at

this depth.

• Make the desired cut.

• For better quality cuts and a longer cutter life, make

a series of cuts, instead of a single cut.

3mm

KW800_E ML p24-41 16-01-2001, 13:4527

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KW800 T1 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KW800 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info