Bedienungsanleitung Black Decker KX1600 (Seite 26 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

531202

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

placed on the

stands (4). Always

point your

heatgun away

from you. Secure

the cable to

prevent pulling

your heatgun off

the stand. Do not

touch the nozzle

and ensure that

nothing is

dropped into the

nozzle. Carefully switch off your heatgun and then

allow it to cool (see cooling down procedure).

FITTING THE SCRAPER (KX1682, KX1683)

Ensure your heatgun is cool.

Align the slot of

the scraper blade

with the

protrusion on the

blade holder and

position under the

retaining screw.

Note: Ensure the hole in the scraper is to the left of the

screw in the blade holder.

Tighten the

retaining screw.

Place the blade

holder over the

nozzle outlet.

Ensure it is

aligned. The small

bump on the

inside of the blade

holder engages with the recess on the nozzle. Tighten

the blade holder clamp screw.

PAINT STRIPPING

When stripping a

point next to

glass, it is

necessary to

protect the glass

from the heat.

A Black & Decker

glass protector

nozzle is used for

this purpose (available as an accessory). Your heatgun

is not suitable for stripping metal framed windows.

This is because the heat from the heatgun is

conducted through the metal and can crack the glass.

Scrape with the grain of the wood wherever possible.

Do not linger on one spot for too long as the surface

may char or ignite.

KX1682, KX1683 only:

Your heatgun is designed for use with the scraper

blade to strip paint.

Proceed as follows:

Ensure the nozzle

is cool and fit the

scraper blade.

Hold your heatgun

with the scraper

blade in contact

with the surface

at an angle of 30-40˚.

When the paint softens, scrape firmly. Experiment to

establish the length of time necessary to apply the heat

to obtain optimum results. Scrape the softened paint

immediately or it will harden again.

Take care to prevent paint and debris collecting on the

scraper because it may ignite. Carefully clean the

scraper blade with a knife should any build up occur.

When scraping vertical surfaces, scrape downwards

to prevent debris falling into the nozzle.

Note: When stripping a point next to glass, use a glass

protector nozzle instead of the scraper blade - a

manual scraper is needed to scrape off the paint.

CD700, KX1600 only:

Your heatgun is designed to soften paint and laquer

enabling it to be removed using a good quality

hand scraper.

Proceed as follows:

Direct the hot air onto the area to be removed. When

the paint softens, scrape firmly. Experiment to establish

the length of time necessary to apply the heat to obtain

optimum results. Scrape the softened paint

immediately or it will harden again.

OTHER USES FOR YOUR HEATGUN

On low heat (KX1682, KX1683):

• Drying paint and varnish.

• Removing stickers and decorations.

• Waxing and dewaxing (eg. ski’s).

• Drying wet timber prior to filling.

• Shrinking PVC wrapping and insulation tubes.

• Thawing frozen pipes.

30-40°

CD700 KX1600-1683 ML p22-39 07/01/2000, 3:39 pm26

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KX1600 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info