Bedienungsanleitung Black Decker KX2001K T1 (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

577931

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Injuries caused by prolonged use of a tool.

When using any tool for prolonged periods

ensure you take regular breaks.

Impairment of hearing.

Health hazards caused by breathing dust

developed when using your tool (example:-

working with wood, especially oak, beech

and MDF.)

Labels on tool

The following pictograms are

shown on the tool:

;

Warning!

To reduce the risk of

injury, the user must read the instruc-

tion manual.

Electrical safety

This tool is double insulated; there-

fore no earth wire is required. Always

check that the power supply cor-

responds to the voltage on the rating

plate.

If the supply cord is damaged, it must be

replaced by the manufacturer or an author-

ised Black & Decker Service Centre in order

to avoid a hazard.

Extension cables

A 2 or 3 core cable may be used as the

appliance is double insulated and of class II

construction.

Up to 30m (100 ft) can be used without loss

of power.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Heat control knob

3. Nozzle

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting an accessory (g. C, D, E & F)

A selected range of accessories can be obtained from your

local retailer.

w Cone nozzle (5): Concentrates the air stream on a

smaller area.

w Fish tail (6): Spreads the air stream over a wider area

w Spoon reector (7): For soldering pipes.

w Glass protector (8): For the protection of glass during

paint stripping.

w Scraper (9): For the removal and stripping paint and

varnish.

u Fit the connecting piece of the accessory over the nozzle

(2).

Use

Setting the temperature (g. A)

u To increase the temperature setting, turn the heat control

knob (2) clockwise.

u To reduce the temperature setting, turn the heat control

knob anti-clockwise.

Switching on and off

u To switch the tool on at the low air speed, low heat, set the

on/off switch to position I.

u To switch the tool on at the high air speed, high heat, set

the on/off switch to position II.

u To switch the tool off, set the on/off switch to position O.

Using the tool

Your tool is tted with a thermostat for your safety. Using the

tool continuously for very long periods or other severe duty

cycles may cause the tool to overheat and the element to stop

working. It is therefore recommended that you allow the tool to

cool down at regular intervals during use.

u Allow the tool to heat up for a few seconds before use.

u At rst use some smoke may emit from the nozzle. This is

normal and will soon decrease.

u Use a low temperature setting for drying paint and varnish,

removing stickers, shrinking insulation tubes, and thawing

frozen pipes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KX2001K T1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info