Bedienungsanleitung Black Decker MT350 (Seite 5 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

529663

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

(Original instructions)

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Forward/reverse slider

3. Head release button

4. Bit holder

5. Drill/screwdriver head (MTDD6)

6. Torque adjustment collar

7. Chuck

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting and removing tool heads (g. A)

Warning! Care must be taken when tting and removing

heads. Moving parts may become hot during use.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u To remove a tool head, depress the head release button

(3) and take the head off the tool.

u To t a tool head, line it up with the tool as shown and

push it onto the tool until it snaps into place.

Fitting and removing a drill bit or screwdriver bit

The drill/screwdriver head is tted with a keyless chuck to

allow for an easy exchange of bits.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u Open the chuck (7) by turning the front part clockwise with

one hand while holding the rear part with the other.

u Insert the bit shaft into the chuck (7).

u Firmly tighten the chuck (7) by turning the front part anti-

clockwise with one hand while holding the rear part with

the other.

u To remove the screwdriver bit from the bit holder, lift the bit

from the recess.

u To store the screwdriver bit, rmly push it into the holder.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Selecting the torque or drill position (g. B)

This tool is tted with a collar to set the torque for tightening

screws.

u For drilling, set the collar (6) to the drilling position by

aligning the symbol with the marking (8).

u For screwdriving, set the collar to the desired setting.

u If you do not yet know the appropriate setting, proceed as

follows:

t Set the collar (6) to position 1.

t Tighten the rst screw.

t If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting.

Selecting the direction of rotation (g. C)

For drilling and tightening screws,

use forward (clockwise) rotation. For loosening screws or

removing a jammed drill bit, use reverse (counterclockwise)

rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker MT350 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info