Bedienungsanleitung Black Decker RS890 T1 (Seite 6 von 12) (Englisch)

581265

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

(Original instructions)

Autoselect (g. B)

The Autoselect feature allow you to set the optimum speed of

the tool dependant on the material you are cutting.

u Slide the Autoselect switch (3) to the top position for cut-

ting sheet metal.

u Slide the Autoselect switch (3) to the middle position for

cutting plastic.

u Slide the Autoselect switch (3) to the bottom position for

cutting wood and metal tubing.

Sawing (g. C)

u If possible, always hold the tool with both hands using the

main handle (7) and secondary handle (8).

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u Keep the shoe/branch steady (5) pressed rmly against

the workpiece.

Pruning branches (g. D & E)

u If possible, always hold the tool with both hands using the

main handle (7) and secondary handle (8).

u Rotate the branch steady (5) till it clicks into place.

u Let the blade run freely for a few seconds before starting

the cut.

u Position the saw so that the blade is above the branch and

the branch steady (6) is below the branch.

u Apply only a gentle pressure to the tool while performing

the cut.

u For proper cutting, the branch being cut should be in con-

tact with both sides of the pruning shoe. The cut should

be square to the branch, and not made at an angle. If

required a rotating action could be used to further improve

the speed of the pruning cut.

Warning! The branch steady (6) is not a handle and should

never be used as a handle. Always hold the tool using the

main handle (7) and the secondary handle (8 or 9).

Operating in jigsaw mode (g. F)

u If possible, always hold the tool with both hands using the

main handle (7) and secondary handle (9).

u Rotate the branch steady (5) till it clicks into place.

u Fit the required blade.

Hints for optimum use

u Do not exert too much pressure on the tool.

u Regularly check the condition of accessories. Replace

when necessary.

Sawing wood

u Clamp the workpiece securely and remove all nails and

metal objects.

u When splintering is to be minimised, e.g. when cutting

laminates, clamp a piece of scrap wood or hardboard to

both sides of the workpiece and saw through this sand-

wich.

Sawing metal

u Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Cutting branches

u Cut downward and away from your body.

u Make the cut close to the main branch or tree body.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker RS890 T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker RS890 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info