Bedienungsanleitung Black Decker SMS254 T1 (Seite 14 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578656

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

ENGLISH

Blade and tooth type

Your mitre saw has been supplied with a negative rake saw

blade. It is advisable to use a negative rake saw blade.

 TCG type - For cutting aluminium sheets, tubing

extrusions and other non-ferrous metals such as

copper, brass.

 ATB type - For general cutting and trimming of wood,

plywood, and sizing pressboard, hardboard, and

particle board, when a neat cut is needed.

Always use a negative rake blade when cutting non-ferrous

metals.

Changing blades (fig.O - Q)

Warning! To avoid injury from accidental starting, always

remove the power plug from the power source before

changing the blades. Use correctly sharpened saw blades.

Observe the maximum speed and tooth type marked on the

saw blade. Only use Black & Decker recommended blades.

To replace the saw blade (35), proceed as follows:

 Press the saw arm release lever (37) and rotate the

moveable lower guard counter clockwise and clear of

the blade. Use one hand to hold the guard in place

(fig. O).

 Using a screwdriver, loosen but do not remove the

screw (50). Do not remove the screw completely as this

will make re-assembly difficult.

 Using a screwdriver, loosen but do not remove the

screw (51) until there is movement in the metal guard

plate. Do not remove the screw completely as this will

make re-assembly difficult.

 Move the metal upper guard plate counter clockwise

(fig. P). This will give you access to the spindle bolt (52)

that attaches the saw blade (35) to the mitre saw.

 Press and hold the spindle lock button (36) on the motor

housing, to lock the saw blade (35) and prevent it from

rotating.

 Using the supplied blade spanner, turn the spindle

bolt (52) in a clockwise direction to remove the bolt and

the saw blade (35).

 Fit a replacement blade, make sure that the teeth are

pointing downward and the direction marking on the

blade is the same as that on the mitre saws guard

(clockwise) (fig. P).

 Loosely fit the spindle bolt (52) by hand (turn counter

clockwise).

 Press and hold the spindle lock button (36) and use the

blade spanner to tighten the spindle bolt (52) until the

blade is secure.

 Replace the metal upper guard (26) into its original

position and tighten the two screws (50 and 51).

 Allow the moveable lower guard (5) to return to its

original position covering the blade.

Warning! Never press the spindle lock while the blade is

rotating. Be sure to hold the guard bracket down and firmly

tighten the guard bracket screw after installing the blade.

Warning! The guard bracket must be returned to its original

position and the screw tightened before activating the saw.

Failure to do so may allow the guard to contact the spinning

saw blade resulting in damage to the saw and severe

personal injury.

Accessories

The performance of your tool depends on the accessory

used. Black & Decker and Piranha accessories are

engineered to high quality standards and designed to

enhance the performance of your tool. By using these

accessories you will get the very best from your tool.

Warning! Do not carry the machine by the guard.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regular cleaning. Regularly clean the ventilation slots with a

clean, dry paint brush. To clean the tool, use only mild soap

and a damp cloth. Never let any liquid get inside the tool and

never immerse any part of the tool into liquid.

Warning! Before carrying out any maintenance, make sure

that the tool is switched off and unplugged.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

 Safely dispose of the old plug.

 Connect the brown lead to the live terminal in the new

plug.

Material Tooth type 600 ~ 100T 24 ~100T

TCG ATB

Wood Lumber

••

Plywood

••

Hardboard

••

Chipboard

••

Plastic PVC

•

ABS

•

Acrylic

•

Non-ferrous

metal

Aluminium

•

Copper

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker SMS254 T1 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker SMS254 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info