Bedienungsanleitung Black Decker SMS254 T1 (Seite 11 von 20) (Englisch)

578656

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

23. 33.9° bevel pin

24. Rear carry handle

25. Saw dust outlet

26. Metal upper guard

27. Front carry handle

28. Removable brush box

29. Carriage

30. Bevel lock handle

31. Bevel scale

32. Right-hand fence

33. Laser

34. Saw blade

35. Spindle lock button

36. Saw arm release lever

Fig. R

53. Clamp

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Note: This tool is accurately adjusted before shipping from

the factory. Check the following accuracy and readjust them

if necessary in order to obtain the best results in operation.

Laser beam

The laser beam alignment is set at the manufacturing source

and is not user adjustable.

Mitre angle adjustment

The sliding compound mitre saw scale can be easily read

showing mitre angles from 0° to 47° to the left and the right.

The most common angle cut setting slots have positive

stops, permitting fast adjustments to the required position.

Follow the process below for quickest and most accurate

adjustments.

Superlok

mitre clamp (fig. B)

The Superlok

mitre clamp (9) allows the saw to be set to

specific angles other than the preset angles of 0°, 15°, 22.5°,

31.6°, and 47° which are set using the mitre detent lever (11).

Adjusting the bevel stops at 90° and 45° (fig. C - F)

 Loosen the bevel lock handle (30) and move the cutting

head all the way to the right and tighten the bevel lock

handle.

 Use a square to set the blade at 90° to the table (fig. D).

 If an adjustment is necessary, loosen the lock nut (41)

and adjust the bolt (40) with the wrench so that the blade

is 90° to the table.

 Tighten the lock nut (41).

 Align the bevel indicator (39) with the 0° mark by

adjusting the screw (38).

When adjusting the 45° stop, make sure that the left-hand

high sliding fence (22) is adjusted so that the cutting head

can be moved to the 45° position (fig. E).

 Release the high sliding fence clamp (20) and move the

high sliding fence (22) away from the blade.

 Tighten the high sliding fence clamp (20).

 Pull out the 33.9° bevel pin (23) and follow the same

procedures for the 90° but move the cutting head to the

left and use the lock nut (43) and adjustment bolt (42).

Adjusting the fence (fig. G - H)

 Lower the cutting head and push in the lock pin (46).

Make sure that the table is in 0° mitre position.

 Place a combination square against the left-hand fence

(21) and next to the saw blade (34) (fig. G).

 If the blade does not contact the square along it’s length,

loosen the three screws (44) (fig. H) and adjust the

fence.

 Tighten the three screws (44).

Bench mounting (fig. I)

Note: We highly recommend that you bolt this mitre saw

securely to a work bench to gain the maximum stability of

your machine. Make sure that the machine is fixed to a

bench whenever possible.

 Locate and mark the four bolt holes on the bench.

 Drill the bench with an Ø10 mm drill bit.

 Bolt the mitre saw onto the bench with bolts, washers

and nuts.

Note: These fasteners are not supplied with the tool.

Use

 Place your hands no closer that 150 mm from the blade.

 Hold the workpiece tightly to the table and the fence

when cutting. Keep your hands in position until the

switch has been released and the blade has completely

stopped.

 Always make dry runs (without power) before finish cuts

so that you can check the path of the blade.

 Do not cross your hands.

 Keep both feet firmly on the floor and maintain proper

balance.

 As you move the saw arm left and right, follow it and

stand slightly to the side of the saw blade.

 Sight through the guard louvres when following a pencil

line.

Basic pullover mitre saw operations (fig. H)

 Always use the clamp (53) to hold the workpiece firmly.

Two holes (45) are provided for the clamp (fig. H & R).

Warning! Make sure that the workpiece is securely held in

place with the clamp before operation. Severe personal

injury can occur if the workpiece is not secured.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker SMS254 T1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker SMS254 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info