Bedienungsanleitung Black Decker STC1820D (Seite 9 von 112) (Alle Sprachen)

606056

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

(Original instructions)

Adjusting the position of the secondary handle (g.

The second handle (5) can be adjusted to provide optimum

balance and comfort.

u Press in the button (15) on the left side of the handle.

u Rotate the second handle (5) into the required position.

u Release the button (15).

Warning! Ensure that the teeth on the button are correctly

aligned in slots in the handle and that the handle is secure.

Adjusting the height of the tool (g. E)

This tool has a telescopic mechanism, allowing you to set it to

a comfortable height. There are multiple height settings.

To adjust the height setting, proceed as follows:

u Loosen the adjustment collar (16) by turning it clockwise.

u Gently pull the tube (17) in or out of the handle (2) to the

desired height.

u Tighten the adjustment collar (16) by turning anti-clock-

wise.

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

Warning! Before assembly, remove the battery from the tool.

u Remove the tape holding the cutting line to the spool

housing (7).

Fitting and removing the battery (g. F)

u To t the battery (4), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (18) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. G)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (4), insert it into the charger (19).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (20) will ash green continuously

(slowly).

The charge is complete when the charging indicator (20)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging indica-

tor (20) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator (20) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (4).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 30 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Setting the tool to trimming or edging mode (g. H,

I, J & K)

The tool can be used in trimming mode as shown in g. H or

in edging mode to trim overhanging grass along lawn edges

and ower beds as shown in g. I.

Trimming mode (g. E, H & J)

For trimming, the trimmer head should be in the position

shown in g. J. If it is not:

u Remove the battery from the tool.

u Loosen the adjustment collar (16) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8) clock-

wise.

u Tighten the collar (16) by turning it anti-clockwise.

Note: Note: The head will only rotate in one direction.

Edging mode (g. E, I & K)

For edging, the trimmer head should be in the position shown

in g. K. If it is not:

u Remove the battery from the tool.

u Loosen the adjustment collar (16) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8) anti-

clockwise.

u Tighten the collar (16) by turning it anti-clockwise.

Note: The head will only rotate in one direction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker STC1820D Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info