10
ENGLISH
(Original instructions)
11
ENGLISH
(Original instructions)
The green LED will ash indicating that the battery is being
charged.
The completion of charge is indicated by the green LED
remaining on continuously
may be used at this time or left in the charger
Warning! Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished.
Charger diagnostics
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems
are indicated by one LED ashing in different patterns.
Bad Battery
The charger can detect a weak or damaged battery
red LED ashes in the pattern indicated on the label. If you
see this bad battery blink pattern, do not continue to charge
the battery
for recycling
Hot/Cold Pack Delay
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a Hot/Cold
Pack delay
normalised.
switches to the Pack Charging mode. This feature ensures
maximum battery life. The red LED ashes in the pattern
indicated on the label when the Hot/Cold pack delay is
detected.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely
pack fresh and fully charged.
Important charging notes
u Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack .
u The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. T
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer
u If the battery pack does not charge properly:
u Check current at receptacle by plugging in a lamp or
other appliance
u Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
u Move charger and battery pack to a location where the
surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
u If charging problems persist, take the appliance, battery
pack and charger to your local service center
u The battery pack should be recharged when it fails to
produce sufcient power on jobs which were easily done
previously
conditions. Follow the charging procedure. Y
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities.
when there is no battery pack in the cavity
before attempting to clean.
u Do not freeze or immerse charger in water or any other
liquid.
Warning! Shock hazard. Do not allow any liquid to get inside
charger
reason.
If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
Installing and removing the battery pack from the
appliance
Warning! Make certain the lock-of
prevent switch actuation before removing or installing battery
T
Insert battery (12) into appliance until an audible click is
heard (Figure B). Ensure battery pack is fully seated and fully
latched into position.
T
Depress the battery release button (13) as shown in Figure C
and pull battery pack out of appliance.
Assembly
Warning! Before assembly
switched off and the battery has been removed.
Assembly tools required (not supplied):
Phillips Screwdriver
Fitting the guard (Fig. D, E)
Warning! Remove the battery from the appliance before
attempting to attach the guard, edge guide or handle. Never
operate appliance without guard rmly in place. The guard
must always be on the appliance to protect the user
u Remove the screw from the guard.
u T
down at the spool cap (14).
u T
motor housing (15). Make sure the tabs (16) on the guard
engage the ribs (17) on the motor housing as shown.
u Continue to slide the guard on until you hear it “snap” into
place. The locking tab (18) should snap into the housing
slot (19).
u Using a phillips screwdriver
tighten securely as shown in Figure E to complete the
guard assembly
u Once the guard is installed, remove the covering from the
line cut-off blade, located on the edge of the guard
Warning! Never use the tool unless the guard is properly
tted.
Attaching the auxiliary handle (Fig. F
u T
sides of the upper housing as shown in Figure F
u Position the handle as shown in Figure G (with the
BLACK+DECKER logo facing upward). Partially push the
handle on so it will hold the buttons in when you release
them with your hand.
u Push the handle completely onto the housing and position
it slightly until it “snaps” into place.
u T
(21) and raise or lower the handle (Figure H).
u The handle should be adjusted so that your front arm is
straight when the trimmer is in the working position.
Height adjustment (Fig. I, J–J3)
Warning!
working positions shown in Figures J - J3.
u The overall height of the trimmer can be adjusted by
loosening the height-adjust collar (6) by rotating it in the
direction of the arrow shown in Figure I.
u Move the upper housing straight up or down. When the
desired height is achieved, tighten the collar by rotating it
opposite of the direction shown in Figure I.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
u Remove the tape holding the cutting line to the spool
housing.
Operation
Warning!
Warning! Before you begin trimming, only use the appropriate
type of cutting line.
Note: Inspect area to be trimmed and remove any wire, cord,
or string-like objects which could become entangled in the
rotating line or spool. Be particularly careful to avoid any wire
which might be bent outwardly into the path of the appliance,
such as barbs at the base of a chain link fence.
Switching on and off
u T
and squeeze the trigger (1).
u T
Operating the trimmer (Fig. I, J–J3)
u With the unit on, angle unit and slowly swing the trimmer
side to side as shown in Figure J.
u Maintain a cutting angle of 5° to 10° as shown in
Figure J1. Do not exceed 10° (Figure J2). Cut with the tip
of the line. T
wheel (9).
u Maintain a minimum distance of 60 cm between the guard
and your feet as shown in Figure J3. T
distance adjust the overall height of the trimmer as shown
in Figure I.
Convert to edging mode (Fig. K, L)
Warning!
in the edging mode.
The trimmer can be used in trimming mode or edging mode to
trim overhanging grass along lawn edges and ower beds. For
edging, the trimmer head should be in the position shown in
Figure M. If it is not:
u Remove the battery from the trimmer
u Grasp the ip-to-edge collar (7) and push down as
shown in part 1 of Figure L.
u Rotate the ip-to-edge collar 180° counterclockwise as
shown in part 2, until the handle snaps back into the
upper half of the trimmer
u T
down and rotate the head clockwise back to its original
position.
Note: Y
if the trimmer line is positioned directly over the sidewalk or
abrasive surface.
