Bedienungsanleitung Black Decker VN2010 (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

55643

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

Adjusting the suction head (fig. A)

X For vacuuming on carpets, switch the floor surface selector

(25) into the up position.

X For vacuuming on laminates, tiles, etc., switch the floor

surface selector (25) into the down position.

Switching on and off

X The on/off switch (4) can be operated by hand or foot.

X To switch the appliance on, press the on/off switch (4).

X To switch the appliance off, press the on/off switch (4)

again.

Adjusting the airflow (fig. B)

X Rotate the airflow control switch (11) to adjust the airflow

as desired. Max and min positions are shown.

Vacuuming

X When operating the appliance, make sure that the hose is

not trapped, twisted or blocked

X In case of overheating, a cut-out will operate and the

appliance will automatically stop.

X If the appliance stops operating, unplug the appliance and

allow it to cool for 2-3 hours.

Hints for optimum use

X When working in confined spaces, temporarily remove the

accessory holder from the tube to improve your scope.

X When vacuuming stairs, always start at the bottom and

work your way up. Position the appliance on the floor and

do the stairs until halfway. Then carry the appliance to a

stable position which is at least one stair below your

working position, and do the top half of the stairs.

VN2200 - Using the turbo brush (fig. A)

X Take care that the speed control switch is at the highest

setting. Move the slider on top of the brush as necessary to

optimise the suction force.

X Move the brush steadily back and forth. Do not keep the

brush on the same place for a long time, as this might

damage the surface.

Carrying the appliance (fig. C)

During use the appliance can be carried using the handle (5).

X Tilt the handle into position as shown.

Temporarily parking the suction head (fig. D)

X Use the park position for a temporary parking of the suction

head.

Storing the appliance (fig. E & F)

Warning! Warning! When storing the appliance, switch the

appliance off and unplug it.

X Make sure that the cord is fully rewound.

X Place the appliance in an upright position.

X Wrap the hose around the appliance.

X Insert the suction head hook (26) into the recess in the

appliance.

X Push the tube until the locking device (27) inserts into the

corresponding recess in the appliance as shown. The

locking device (27) engages automatically.

X Store the appliance in a dry location. The appliance can be

carried by the container handle (2).

X To take the tube from the appliance for use, press the lever

on the locking device (27) on the back of the tube and pull

the tube away from the unit and lift the tube and head out

of the parking slots.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Cleaning the filter

The appliance is fitted with a filter cleaning feature.

X After every use switch the appliance off but don't unplug

from the mains.

X Ensure the container is securely in place.

X Press the filter cleaning switch (3) and the filter cleaning

cycle will run for 10 seconds, after which it will

automatically switch off. During the 10 seconds, the auto

cleaning system cleans the filter.

X The plug can now be removed from the socket.

This will ensure that the next time the appliance is used the

performance is at its optimum.

Note: The appliance is designed to prevent vacuuming

during the filter cleaning cycle. If the vacuum is switched on

during the filter cleaning cycle, the filter cleaning cycle will

stop.

Warning! Before performing any maintenance or cleaning on

the appliance, unplug the appliance.

X Regularly clean the ventilation slots in your appliance using

a soft brush or dry cloth.

X Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

VN2200 - Clearing the turbo brush (fig. G)

X Remove any hair or threads collected onto the brush (28).

Use a pair of scissors if necessary.

X Remove the cover (29) to remove any foreign objects

blocking the air turbine (30). Re-fit the cover.

Emptying the container (fig. H & I)

The container (9) must be emptied when the dirt fills to the

maximum mark indicated on the bin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker VN2010 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info