Bedienungsanleitung Black Decker xta 71 k (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

389511

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Addition safety instructions for sanders

X Always wear a dust mask whenever sanding.

X Thoroughly remove all dust after sanding.

X Take special care when sanding paint which is possibly

lead based or when sanding some woods and metal which

may produce toxic dust:

- Wear a dust mask specifically designed for protection

against lead paint dust and fumes and ensure that

persons within or entering the work area are also

protected.

- Do not let children or pregnant women enter the work

area.

- Do not eat, drink or smoke in the work area.

- Dispose of dust particles and any other debris safely.

- Before using the tool on wooden workpieces, make

sure to fit the dust cassette.

X Before using the tool on metal workpieces, make sure to

remove the dust cassette.

X Never use the tool without a sanding sheet.

X Never use the tool without a sanding base.

X This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

X If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

Features

1. On/off switch

2. Cover

3. Dust cassette

4. Dust extraction outlet

5. Sanding base

6. Paper clamp lever

7. Paper punch

8. Filter

9. Vacuum pipe adaptor

Assembly

Warning! Before assembly, make sure that the tool is switched

off and unplugged.

Fitting sanding sheets (fig. A - B)

Warning! Never use the tool without a sanding sheet or

accessory in place.

Fitting sanding sheets with nylon loops (fig. A)

Warning! Make sure that the tool is switched off and

unplugged.

X Press the sheet firmly and evenly onto the sanding base (5),

making sure that the holes in the sheet line up with the

holes in the base.

Fitting regular sanding sheets (fig. B)

Warning! Make sure that the tool is switched off and

unplugged.

X Soften the sanding sheet by rubbing its non-abrasive side

over the edge of a worktop.

X Press the paper clamp levers (6) upwards to release them

from the retaining grooves and open the paper clamps by

pressing them down.

X Place the sheet onto the sanding base.

X Insert the edge of the sanding sheet into the front paper

clamp as shown.

X Press the front paper clamp lever (6) downwards and locate

it in the retaining groove.

X While keeping a slight tension on the sheet, insert the rear

edge of the sheet into the rear paper clamp.

X Press the rear paper clamp lever (6) downwards and

X locate it in the retaining groove.

Punching sanding sheets (fig. C)

The paper punch (7) is used for punching dust extraction

holes in sanding sheets without pre-punched holes.

Fit a sanding sheet.

X Hold the tool in position right above the paper punch (7).

X Press the tool with the sanding base (5) down into the

paper punch.

X Take the tool off the paper punch (7) and check whether the

holes in the sanding sheet have been fully pierced.

Fitting and removing the dust cassette (fig. D)

X Fit the dust cassette (3) over the dust extraction outlet (4).

X To remove the dust cassette (3), pull the dust cassette to

the rear and off the outlet (4).

Use

Warning! Let the tool work at its own pace.

Warning! Do not overload.

Switching on and off (fig. E)

X To switch the tool on, press the part of the on/off switch (1)

marked ‘I’.

X To switch the tool off, press the part of the on/off switch (1)

marked ‘0’.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker xta 71 k Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info