Bedienungsanleitung Black Decker xtc 143 bk (Seite 6 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388359

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

3. Chuck

4. Mode selector / torque adjustment collar

5. Three-gear selector

6. Bit holder

7. Battery

8. Side handle

Fig. A

9. Charger

10. Charging indicator

11. End of charge indicator

Assembly

Warning! Before assembly, remove the battery from the tool.

Fitting and removing the battery (fig. B)

◆ To fit the battery (7), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

◆ To remove the battery, push the release button (12) while

at the same time pulling the battery out of the receptacle.

Fitting the battery cap (fig. C)

Warning! Fit the cap (13) to the battery (7) for transportation

and storage.

Fitting the side handle

◆ Loosen the side handle (8) by turning it counterclockwise.

◆ Slide the side handle over the chuck and onto the

housing.

◆ Tighten the side handle by turning it clockwise.

Fitting and removing a drill bit or screwdriver bit (fig. D)

This tool is fitted with a keyless chuck to allow for an easy

exchange of bits.

◆ Lock the tool by setting the forward/reverse slider (2) to

the centre position.

◆ Open the chuck by turning the sleeve (14) with one hand

while holding the tool with the other.

◆ Insert the bit shaft (15) into the chuck.

◆ Firmly tighten the chuck by turning sleeve (14) with one

hand while holding the tool with the other.

This tool is supplied with a double-ended screwdriver bit in

the bit holder (6).

◆ To remove the screwdriver bit from the bit holder, lift the

bit from the recess.

◆ To store the screwdriver bit, firmly push it into the holder.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. A)

The battery needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery for the

first time, or after prolonged storage, it will only accept an

80% charge. After several charge and discharge cycles, the

battery will attain full capacity. The battery may become warm

while charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery (7), remove it from the tool and

insert it into the charger (9). The battery will only fit into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

◆ Plug in the charger.

◆ Check if the red charging indicator (10) lights up. If the

green end of charge indicator (11) lights up now instead,

the battery is too hot and cannot be charged. If this

happens, remove the battery from the charger, let the

battery cool down for approx. 1 hour and re-insert it.

After approx. 30 minutes of charging, the red charging

indicator (10) will stop lighting and the green end of charge

indicator (11) will light up. The battery is now fully charged.

◆ Remove the battery from the charger.

Selecting the direction of rotation (fig. E)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (2) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

◆ To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the operating mode or torque (fig. F)

This tool is fitted with a collar to select the operating mode

and to set the torque for tightening screws. Large screws and

hard workpiece materials require a higher torque setting than

small screws and soft workpiece materials. The collar has a

wide range of settings to suit your application.

◆ For drilling in wood, metal and plastics, set the collar (4)

to the drilling position by aligning the symbol

with the

marking (16).

◆ For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker xtc 143 bk Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info