Bedienungsanleitung Black Decker xtc 60 k (Seite 5 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

381452

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

The charger automatically shuts off if the ambient

temperature becomes too high. As a consequence

the charger will be inoperable. The unit must be

disconnected from the mains supply and taken to an

authorised service centre for repair.

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Overview

1. Forward/reverse switch

2. Bit holder sleeve

Fig. A

3. Charger connector

4. Charger

5. Charger plug

Assembly

Fitting and removing a drill bit, socket driver bit or

screwdriver bit (fig. B)

This tool uses socket driver bits, screwdriver bits and drill bits

with a 1/4" (6.35 mm) hexagonal shank.

◆ Pull back the bit holder sleeve (2).

◆ Insert the bit shaft (6) into the bit holder.

◆ Release the bit holder sleeve.

Use

Charging the battery (fig. A)

The battery needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery for the

first time, or after prolonged storage, it will only accept an

80% charge. After several charge and discharge cycles, the

battery will attain full capacity. The battery may become warm

while charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery, insert the charger plug (5) into the

connector (3). Make sure that the head is in straight

position.

◆ Plug in the charger (4). Switch on at the mains.

◆ Leave the tool connected to the charger for 6-8 hours.

The charger may hum and become warm while charging;

this is normal and does not indicate a problem.

Generally, a charging time of 6 hours will enable the tool to

operate at an effective power level for most tasks. However,

further charging for up to 8 hours could significantly increase

the run time, depending on the battery and charging conditions.

◆ Before using the tool, unplug the charger and disconnect

the tool from the charger.

Warning! Do not use the tool while it is connected to the

charger.

Drilling/screwdriving (fig. C)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

◆ To switch the tool on in forward rotation press the upper

button on the forward/reverse switch (1).

◆ To switch the tool on in reverse rotation press the lower

button on the forward/reverse switch (1).

◆ To switch the tool off, release the switch.

Hints for optimum use

Drilling

◆ Always apply a light pressure in a straight line with the

drill bit.

◆ Just before the drill tip breaks through the other side of

the workpiece, decrease pressure on the tool.

◆ Use a block of wood to back up workpieces that may

splinter.

◆ Use HSS drill bits when drilling in metal.

◆ Use a lubricant when drilling metals other than cast iron

and brass.

◆ Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

◆ Always use the correct type and size of screwdriver bit.

◆ If screws are difficult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

◆ Always hold the tool and screwdriver bit in a straight line

with the screw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker xtc 60 k Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info