Bedienungsanleitung Black Decker xtd 24 ck (Seite 5 von 12) (Englisch)

388855

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

f. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power tool

for operations different from those intended could result

in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for hammer drills

◆ Wear ear protectors. Exposure to noise can cause

hearing loss.

◆ Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

◆ Preferably wear a dust mask.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Tool holder

6. Side handle

7. Depth stop

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle and depth stop (fig. A)

◆ Turn the grip counterclockwise until you can slide the side

handle (6) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Insert the depth stop (7) into the mounting hole as shown.

◆ Set the depth stop to the desired position. The maximum

drilling depth is equal to the distance between the tip of

the drill bit and the front end of the depth stop.

◆ Tighten the side handle by turning the grip clockwise.

Fitting an accessory (fig. B)

◆ Clean and grease the shank (9) of the accessory.

◆ Pull back the sleeve (10) and insert the shank into the tool

holder (5).

◆ Push the accessory down and turn it slightly until it fits

into the slots.

◆ Pull on the accessory to check if it is properly locked.

The hammering function requires the accessory to be able

to move axially several centimetres when locked in the

tool holder.

◆ To remove the accessory, pull back the sleeve (10) and

pull out the accessory.

Fitting the keyed chuck (fig. C)

◆ Fit the shank (9) of the supplied chuck (11) into the tool

holder as described above.

Warning! Never use standard chucks in the hammer drilling

mode.

Fitting accessories in the keyed chuck (fig. D)

◆ Open the chuck by turning the sleeve (10).

◆ Insert the bit shaft (12) into the chuck.

◆ Insert the chuck key (13) into each hole (14) in the side of

the chuck and turn until tight.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, floors or ceilings, check

for the location of wiring and pipes.

Selecting the operating mode (fig. E)

The tool can be used in three operating modes. Rotate the

drilling mode selector (5) towards the required position, as

indicated by the symbols.

Drilling

◆ For drilling in steel, wood and plastics, and for screwdriving

set the operating mode selector (5) to the position.

◆ When screwdriving, start at a low speed.

Hammer drilling

◆ For hammer drilling in masonry and concrete, set the

operating mode selector (5) to the position

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker xtd 24 ck Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info