Bedienungsanleitung Black Decker xts 1660 ka (Seite 7 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

383510

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

◆ Fit the outer washer (15) on the spindle, with the raised

part pointing away from the saw blade.

◆ Insert the blade retaining screw (14) into the hole.

◆ Keep the spindle lock button (5) depressed.

◆ Securely tighten the blade retaining screw by turning it

clockwise using the spanner (12) supplied.

◆ Adjust the riving knife as described below.

Adjusting the riving knife (fig. B)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

◆ Loosen the screws (17), using the spanner (12), while

holding the riving knife in position. You will need to

reduce the depth of cut to obtain access to the screws.

◆ Position the riving knife (9) as shown.

◆ The distance between the toothed rim and the riving knife

should be 2 - 3 mm.

◆ The height difference between the toothed rim and the

lower end of the riving knife should be 2 - 3 mm.

◆ Tighten the screws.

Fitting and removing the parallel fence (fig. C)

◆ The parallel fence is used to saw in a straight line parellel

to the edge of the workpiece.

Fitting

◆ Loosen the locking knob (18).

◆ Insert the parallel fence (10) through the openings (19).

◆ Slide the parallel fence into the desired position.

◆ Tighten the locking knob.

Removing

◆ Loosen the locking knob.

◆ Pull the parallel fence out of the tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

This tool can be used in the right hand or the left hand.

Adjusting the blade angle (fig. D)

The default angle between the saw blade and the shoe

is 90°.

◆ Use a square to check that the angle between the saw

blade and the shoe is 90°. If the angle does not measure

90° adjust as follows:

◆ Loosen the locking knob (20) to unlock the saw shoe.

◆ Screw the adjusting screw (21) in or out to achieve a 90°

angle.

◆ Tighten the locking knob to lock the saw shoe in place.

Adjusting the depth of cut (fig. E)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx. 2 mm.

◆ Loosen the lever (22) to unlock the saw shoe.

◆ Move the saw shoe (6) into the desired position. The

corresponding depth of cut can be read from the scale (23).

◆ Tighten the lever to lock the saw shoe in place.

Adjusting the bevel angle (fig. F)

This tool can be set to bevel angles between 0° and 45°.

◆ Loosen the locking knob (20) to unlock the saw shoe.

◆ Move the saw shoe (6) into the desired position. The

corresponding bevel angle can be read from the scale (24).

◆ Tighten the locking knob to lock the saw shoe in place.

Switching on and off

◆ To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

◆ To switch the tool off, release the on/off switch.

Sawing

Always hold the tool with both hands.

◆ Let the blade run freely for a few seconds before starting

the cut.

◆ Apply only a gentle pressure to the tool while performing

the cut.

◆ Work with the shoe pressed against the workpiece.

Hints for optimum use

◆ As some splintering along the line of cut on the top side

of the workpiece cannot be avoided, cut on the side

where splintering is acceptable.

◆ Where splintering is to be minimised, e.g. when cutting

laminates, clamp a piece of plywood onto the top of the

workpiece.

Using the sight guide (fig. G)

The tool is equipped with a sight guide for straight cutting (25)

and for 45° mitre cutting (26).

◆ Adjust the sight guide as described below.

◆ Align the left edge of the guides (25) or (26) with the

cutting line (27).

◆ Keep the sight guide aligned with the cutting line while

sawing.

◆ Work with the shoe pressed against the workpiece.

Adjusting the sight guide

◆ Make a test cut halfway through a piece of scrap wood.

◆ Withdraw the saw so the cutting line (27) becomes

visible.

◆ While keeping the saw in this position, loosen the sight

guide on the saw shoe as shown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker xts 1660 ka Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info