Bedienungsanleitung Black Decker xtw 1500 eka (Seite 8 von 16) (Englisch)

426958

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Fitting the distance piece (fig. E)

◆ Fit the distance piece (14) to the base of the router using

the screws provided.

Fitting the centring pin (fig. F)

◆ Fit the edge guide to the router as shown in fig. B,

but upside down.

◆ Fit the centring pin (15) to the workpiece side of the edge

guide with the screw (25) provided.

Fitting the copy follower (fig. G)

◆ Fit the edge guide to the router as shown in fig. B.

◆ Fit the ‘L’ bar (16) to the upper side of the edge guide

using the two screws and nuts provided.

◆ Adjust the rotating attachment (26) on the ‘L’ bar with the

wing knob (27).

Fitting the additional edge guide (fig. H)

The additional guide (21) is designed to allow routing of a thin

piece of wood (e.g. the edge of a door).

◆ Adjust the edge guide (12) as necessary.

◆ Loosen the fixing screws (28).

◆ Fit the edge guide (21) to the bars (19) protruding from the

router base.

◆ Adjust the edge guide so the workpiece becomes clamped

between the two edge guide.

◆ Tighten the fixing screws (28).

Use

Warning! Let the tool work at its own pace. Do not overload.

◆ Carefully guide the cable in order to avoid accidentally

cutting it.

Adjusting the depth of cut (fig. I, J & K)

The depth of cut is the distance X between the depth stop bar

(9) and the depth stop (29). The depth of cut can be set in two

different ways as described below.

Adjusting the depth of cut using the scale (fig. J)

◆ Fit the router bit as described above.

◆ Loosen the locking screw (30).

◆ Pull the plunge lock lever (5) up.

◆ Plunge the router down until the router bit touches the

workpiece.

◆ Push the plunge lock lever (5) down.

◆ Move the depth stop bar (9) down against the depth stop

using the depth stop adjuster (31). Reset the scale by

aligning the zero marking (32) with the arrow (33).

◆ Move the depth stop bar (9) to the calculated position

using the depth stop adjuster (31). One quarter turn

corresponds to approx. 6.25 mm.

◆ Tighten the locking screw (30).

◆ Fine adjust using the adjusting knob (34). One full turn

corresponds to approx. 1 mm.

◆ Pull the plunge lock lever (5) up and return the router to its

original position.

◆ After switching the router on, plunge it down and make

the desired cut.

Adjusting the depth of cut using a piece of wood (fig. K)

◆ Fit the router bit and plunge the router down as described

above.

◆ Loosen the locking screw (30).

◆ Move the depth stop bar (9) up using the depth stop

adjuster (31).

◆ Place a piece of wood with a thickness equal to the

desired depth of cut between the depth stop (29) and the

depth stop bar (9).

◆ Move the depth stop bar (9) down against the wood using

the depth stop adjuster (31).

◆ Tighten the locking screw (30).

◆ Fine adjust using the adjusting knob (34).

◆ Remove the piece of wood.

◆ Pull the plunge lock lever (5) up and return the router to its

original position.

◆ After switching the router on, plunge it down and make

the desired cut.

Adjusting the revolver depth stop (fig. L)

After turning the revolver depth stop to the desired setting,

you can fine-adjust the depth stop to be used. If you want to

make several cuts with a different depth of cut, adjust each of

the depth stops.

◆ Turn the depth stop screw (35) up or down as required

using a screwdriver.

Setting the speed

◆ Set the speed control knob (4) to the required speed.

Use a high speed for small diameter router bits. Use a low

speed for large diameter router bits.

Using a batten as a guide (fig. M)

When it is not possible to use the edge guide, for example

when routing grooves in the back panel of a bookcase to

support shelves, proceed as follows:

◆ Select a piece of wood with a straight edge to use as a

batten.

◆ Place the batten onto the workpiece.

◆ Move the batten until it is in the correct position to guide

the tool.

◆ Securely clamp the batten to the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker xtw 1500 eka Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info