Bedienungsanleitung Blaupunkt Berlin RCM 303 A - TravelPilot RG 05 (Seite 2 von 18) (Englisch)

614322

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

- 2 -

2. Testing for interference caused by other electrical equipment

Load the installation disk, select „find compass location“ and then

„compass error“.

Press „reset“, switch on the consumers (e.g. sliding sun roof, rear

window wiper).

The value indicated for „Loc. error“ must be less than 3.5.

Press reset each time you switch on a different piece of electrical

equipment.

After having tested each piece of electrical consumer individually,

check logical combinations as well. The sum of the values for the

consumers must not exceed a „Loc. error“ of 3.5.

If the value registered exceeds 3.5, then you must mount the

magnetic field sensor in a different location.

Note: Do not switch on the rear window defogger while testing for

interference from the electrical equipment. Any interference caused

by the rear window defogger is registered separately during

calibration and then compensated.

Precision resistor for the rear window defogger

(shunt)

The precision resistor has 2 connection wires and 1 measuring wire:

1. Connection to the ground contact of the rear window defogger

(length: 250 cm),

2. Connection to the vehicle chassis (length: 75 cm),

3. Measuring wire to the navigation unit (length: 50 cm), Fig. 3

The mounting location of the precision resistor depends on the length of

the wiring.

Do not lengthen the connection wires for the ground contact and the

vehicle chassis. Do not attach the connection for the vehicle chassis to

the liftback in estate wagons or liftback cars. Select the mounting location

for the precision resistor so that any heat build-up will be eliminated

(chassis metal).

Lay the measuring wire to the navigation unit and connect it to the

corresponding jack of the compact plug, Fig. 3

Note:

No other electrical equipment (e.g. rear window wiper) may be connected

to the ground contact for the rear window defogger, except for the rear

window defogger.

Wheel sensors and magnetic strips Fig. 4

Safety instructions

Never screw the wheel sensor clamp onto any stress-bearing

parts.

Never drill holes in any stress-bearing parts.

Do not attach the sensor wiring to the brake lines or to any

moving parts.

The wheels must be tightened using the torque recommended

by the factory (approx. 100 Nm).

Mount the wheel sensors and the magnetic strips on the free-rolling

wheels, for four-wheel drive cars, on the rear wheels.

In order to mount both the wheel sensors and the magnetic strips, the

vehicle must be jacked up.

Screw the wheel sensors onto the sensor mounts and look for a suitable

mounting location. The sensors must not swing mechanically and they

should be placed in a sheltered location.

While mounting the wheel sensors, it is essential to comply with the

installation tolerances, Fig. 5

Mounting the magnetic strips

After you have found a suitable location for the wheel sensors, you must

determine the position of the magnetic strips on the inside of the wheel

rims. Mark the location selected for the magnetic strip and remove the

wheel.

Before unscrewing the wheel nuts, mark the position of the wheel on the

wheel hub.

Because the magnetic strips are glued into position, the rim must be free

of rust, dirt, grease and water. Clean the inside of the wheel rim

thoroughly (brake cleaning fluid, brake and clutch cleaner).

To ensure that the glue adheres properly, the rims must be at room

temperature.

After thoroughly cleaning and perhaps allowing the rims to warm up, glue

the magnetic strips onto the marked spots over the entire area parallel to

the outer edge of the rim, Fig. 4

Notes

Do not glue the magnetic strips directly onto the edge of the rim, as here

they can be damaged very easily.

Do not piece the magnetic strip together and cut it only at the

marked points (maximum gap between the beginning and end

point, one field = 25 mm).

Mount the wheels and tighten the nuts. Align the wheel sensors in

keeping with the installation tolerances, Fig. 5, and screw them on.

Lay the sensor wires into the interior of the vehicle (use any existing

bushings or drill new holes) and lay them to the navigation unit.

GPS receiver

Mounting the antenna

Important information:

- Mount the antenna on a metal roof only. It is not permissible to

mount the antenna on synthetic roofs or aluminium.

- When mounted on a roof (held only by a magnet), the antenna

must not be exposed to temperatures lying outside a range of -20°

C to +80° C.

- It is not permissible to mount the antenna on roofs covered with

leather or synthetic material.

- Use protective sheathing to protect the antenna wire from being

pinched.

- The adhering surface of the antenna must be free of dirt, snow, ice,

etc.

- You must not lengthen, shorten or bend the antenna wire. Do not

remove the plug during the installation.

- If the antenna is painted with the same colour as the vehicle,

especially paints containing a high percentage of metal, this may

adversely affect the reception. There is no guarantee that the

antenna will operate properly after it has been painted.

Seen from the driving direction, the antenna is to be mounted on the right-

hand side in the rear of the vehicle (passenger’s side, in Great Britain,

driver’s side). On notchback vehicles, mount the antenna on the lid of the

boot using the corner clamps, Fig. 6.

On estate wagons and liftback cars, set the antenna on the roof with its

magnetic foot, Fig. 7.

For a roof mount, remove the corner clamps, Fig. 8.

For estate wagons and liftback cars, lay the antenna wire along the rain

gutter downwards and into the interior of the vehicle, Fig. 9.

Any obstacles near the antenna, such as roof or bicycle carriers, may

adversely affect or even prevent satellite reception.

Lay the antenna wire into the interior of the vehicle and connect the BNC

plug on the antenna wire with the antenna jack on the GPS receiver.

It is advisable to remove the antenna from the roof when driving through

a carwash.

Mounting the GPS receiver

The location for the GPS receiver is dependent on the length of the

antenna wire (2.5 m) and the connection wire to the navigation unit (1.5

m).

Cut the perforated strips into equal lengths and bend them to form corner

clamps, Fig. 10. Screw the clamps onto the GPS receiver using 4 screws

and tooth lock washers. Mount the GPS receiver in a dry spot in the boot

by screwing it on. Do not use screws longer than 7 mm, otherwise you

may destroy the GPS receiver.

Blaupunkt Berlin RCM 303 A - TravelPilot RG 05 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blaupunkt Berlin RCM 303 A - TravelPilot RG 05

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info