Bedienungsanleitung Blaupunkt como rcm 148 (Seite 8 von 21) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

165661

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

- 8 -

Connection

In order to take advantage of the full car radio output and to avoid

incorrect electrical connections with ISO plugs in the vehicle, it is

advisable not to use the vehicle-specific positive/negative connection for

this car radio.

You can avoid making incorrect connections by using the vehicle-

specific Blaupunkt adapter wiring.

Due to the limited cross-section of the wiring in the vehicle, it is necessary

to use the connection cable 7 607 884 093 in addition to the vehicle-

specific Blaupunkt adapter wiring for the positive/negative connection.

Be sure to observe Fig. 4, 5

Positive connection

Cut the permanent +12 volts line from the vehicle-specific Blaupunkt

adapter wiring, join it with connection cable 7 607 884 093 and connect

it directly to the positive terminal of the battery.

Negative connection

Do not connect the negative line to the negative terminal of the battery.

Cut the negative line from the vehicle-specific Blaupunkt adapter wiring,

join it with connection cable 7 607 884 093 and lay the negative line to

a suitable ground, such as a chassis screw, the chassis itself or

corresponding grounds (do not roll up the wiring).

Some vehicles are equipped with a 10-pin plug in the installation

compartment. Do not connect this plug with the car radio as it could

possibly damage the radio (by burning out the printed conductors).

Preparing for the installation of the car radio

The car radio is designed to be installed in the car radio compartment

provided by the vehicle manufacturer. Open the car radio compartment

(remove the shelf or panel by unclipping it) or adjust the size of the car

radio compartment to measure 182 x 53 mm.

For vehicles with deviating installation compartments, Blaupunkt offers

installation kits for 50 mm radio units for the most popular vehicle models.

Check the installation situation in the vehicle and, if necessary, use one

of the special installation kits for specific vehicle models,

e.g. Audi A4/A6/A8: 7 608 021 474

Note:

The mounting bracket included with this car radio is designed for

installation in vehicles with a standard DIN installation compartment

measuring 182 x 53 mm, 165 installation depth and an instrument panel

thickness of approximately 1 to 20 mm in the area of the tab fasteners,

see Fig. 1.

Reach behind the car radio compartment and check to see which tab

fasteners can be bent for the mounting bracket.

Note: Try to be sure to bend all of the tabs.

Place the mounting bracket in the compartment and bend over the tabs

with the help of a screwdriver, see Fig. 1, 2.

Connection

Connection instructions.............................................................. Fig. 4

Positive/negative connection with vehicle-specific

adapter cable ............................................................................. Fig. 5

Positive/negative connection with connection line

7 607 884 093 ............................................................................ Fig. 5a

Equalizer or amplifier connection, (CINCH) ............................... Fig. 6

Do not connect the control wire to terminal 15 (+12 V switched)

or terminal 30 (permanent +12 V), maximum load < 150 mA.

Connection of 4 loudspeakers (4/35 W)..................................... Fig. 7

LF = left front, RF = right front, LR = left rear, RR = right rear.

CD player connection CDC- A06 / CDC- A072 .......................... Fig. 8

Connection of IR remote control RC- 06 .................................... Fig. 9

Use the connection cable attached to the remote control.If

necessary, also use cables 7 607 647 093 and 7 607 648 000.

CD player connection CDC-A05 ................................................Fig. 10

CD player connection CDC-F05 ................................................ Fig. 11

Connection in vehicles with QuickOut

In vehicles equipped with a QuickOut (currently Opel), the QuickOut unit

must be removed and the adapter cable used.

Installing the car radio

Place the car radio in the front of the mounting bracket and push it in until

the side springs snap into position on the left and the right (you will hear

an audible click).

Removing the car radio

Insert the handles into the holes in the panel on the left and right of the

radio and push them in until you hear a distinct click (unlocks side

springs).

Pull the unit out using both handles, see Fig. 3

Note: Handles which have snapped into place can only be

removed after you have pulled the radio out of the

compartment.

This information is subject to change without notice!

Fig. 1

182

165

8 601 310 742

1-20

8 601 910 002

Fig. 2

Fig. 3

Illustrations

8 622 401 356

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt como rcm 148 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blaupunkt como rcm 148

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info