Bedienungsanleitung Blaupunkt GTA 2600 HP (Seite 6 von 36) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

614184

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

GTA 2600 HP

Integrate fuse (25 A)

The fuse integrated in the ampli er protects the output stage

and the entire electrical system in case of a malfunction. If a

replacement fuse is used, never bridge fuses or replace them

with a type with higher current.

Connection examples

Connection of the voltage supply ..................................Fig. 2

Audio inputs ...........................................................................Fig. 3

Loudspeaker connections .................................................Fig. 4 - 7

Remote connection of the ampli er with switchable +12 V

voltage source.

This allows the ampli er to be switched on and o using the

on/o -switch of the car sound system.

Loudspeaker connections

(If the ampli er is to be jumpered, continue with the section

"Bridged loudspeaker connections" at this point).

As with every audio component, the correct polarisation of

ampli er and loudspeakers is of essentially importance for a

good bass response. For this reason, ensure that the positive

connection (+) of the ampli er is connected with the posi-

tive connection (+) of the loudspeaker; the same applies to

the negative connections (-). In addition, the left ampli er

channel must be connected with the left loudspeaker and

the right ampli er channel with the right loudspeaker.

Bridged loudspeaker connections

The GTA ampli er can also be bridged for a mono con gura-

tion. This allows the ampli er to be used for one or several

subwoofers or a mid-range driver. In this con guration, the

ampli er combines the right and left channel to a single-

channel output (mono output).

Note:

The ampli er can add the right and left signal information

only if the right as well as the left cinch (RCA) connection

were carried out.

Caution:

In a bridge circuit, the ampli er load must be 4 Ω or

higher. A lower load leads to an overheating or switch-

o of the ampli er and can cause permanent damages.

Subwoofer connection

The GTA 2600 HP features di erent options of connecting

a subwoofer:

–An active subwoofer or an additional ampli er are

connected with a cinch (RCA) cable to the two LINE OUT

sockets (see Fig.7).

–A passive subwoofer is connected to the bridged loud-

speaker output (see the section "Bridged loudspeaker

connections").

Sound settings

The following options are available to optimise the sound

of the connected loudspeakers:

– BASS switch

The BASS switch is used to adjust the bass response of

the ampli er. The following settings are possible: 0 dB /

+6 dB / +12 dB.

– X-OVER switch and LOW PASS control

For the GTA 2600 HP, the type of frequency crossover

("Low-Pass" or "High-Pass") and the desired cut-o fre-

quency can be adjusted for the connected loudspeakers.

Select the cut-o frequency up to which lower frequencies

(high-pass) or higher frequencies (low-pass) should be

blocked. Only frequencies above the cut-o frequency

(high-pass) or below the cut-o frequency (low-pass) are

passed on to the loudspeakers.

The cut-o frequency is dependent upon the frequency

range of the loudspeakers (see recommended frequency

range of the loudspeakers).

"High-Pass" (switch setting: HI PASS)

With a setting of 80 Hz, the ampli er has a frequency range

from 80 Hz to 30,000 Hz.

"Low-Pass" (switch setting: LOW PASS)

This control is active if the switch is in the LOW PASS posi-

tion, and allows for setting the desired entry frequency.

Example:

At a setting of 150 Hz, the ampli er has a frequency range

of 10 Hz to 150 Hz.

"Full Range" (switch setting: FLAT)

In this switch setting, the frequency control is deactivated

and the entire frequency spectrum is being ampli ed.

– LEVEL control

The LEVEL control is used to adjust the input sensitivity

of the power ampli er to the output voltage of your car

sound system preampli er output. The adjustment range

is from 0.2 V to 5 V. If a car sound system of a third party

manufacturer is connected, the input sensitivity must be

adjusted corresponding to the manufacturer data.

A few important explanations in this context:

By turning the LEVEL control clockwise, the input sen-

sitivity of the ampli er and, therefore, also the volume

increases. However, this is not a volume control. In the

end position, it is not possible to achieve a higher ampli-

 er output, even if it sounds like that at  rst. The system

merely increases the volume faster if the volume control

of the car sound system is turned up.

Power-on indicator (POWER / PROTECT)

Green LED:

Output stage on, regular operating status.

Red LED:

Output stage is electronically switched o due to an error.

GTA_2600_HP_13LG.indd 6GTA_2600_HP_13LG.indd 6 20.08.13 09:4820.08.13 09:48

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt GTA 2600 HP Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info