Bedienungsanleitung Blaupunkt GX 7000 (Seite 13 von 44) (Deutsch, Englisch, Portugiesisch, Spanisch, Polnisch)

686498

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

OPERATING

The mains voltage (230-240V~) indicated on the rating plate must correspond with the mains power supply. Mains connection fuse:

min. 10A.

1. Insert the mains plug of the unit connection cable into the combined switch /plug.

2. Secure with the cable grip. The loop of the mains cable must be adequately long so that the cable grip can slide from one side

to the other.

Switching on the motor

3. Press the On button on the combined switch/plug. Hold down the on button.

4. Pull the safety level against the handle and hold in position – the safety level does not lock into position.

5. Release the On button.

While mowing, lay the connection cable safety on footpaths and on areas which have already been mown. Switching on the motor

1. Release the safety level. The safety lever automatically returns to the zero position.

WARNING: When the motor has been switched o, the cutter continues running for several seconds – therefore do not touch

the underside of the mower until the cutter has come to a standstill. NOTE: Before switching on the unit, always check the

connection cable for signs of damage; only an undamaged connection cable may be used. Damaged connection cables are

highly dangerous

MOWING

1. Before starting the machine adjusts the lawn mower to the cutting height you need. (Refer to section on Lawn Mower Height

Adjustment) 2. Your lawn mower is equipped with a safety switch. To operate the switch, press the lock button then grasp the start

lever to start running. 3. The power will be o when the start lever is released. To start the mower, repeat do step (2) above.

• MOWING PROCEDURE The key to successful electric lawn mowing is a systematic approach to cutting.

Take a few moments to plan your ﬁrst cut using the principles described here.

After one or two uses you will ﬁnd the simplest way of cutting your own particular lawn.

1. Lay cord on ground near outlet in neat, loose coils with mower end of cord on top. It is important to arrange cord systemati-

cally to avoid annoying loops and knots.

2. Starting at point nearest electrical outlet, move back and forth across lawn.

3. Each lawn with its trees, shrubs, and other obstructions requires a diﬀerent mowing procedure. A little experimenting will

enable you to choose the easiest method of handling the cord on your lawn.

EMPTYING THE GRASS BOX

1. When the grass box is full. Switch oﬀ, disconnect the mower from mains supply and wait until blade has come to standstill.

2. Take the handgrip of collection box (13)

3. Lift the grass box backwards.

4. Empty the grass box

WARNING: When the motor has been switched on, the cutter continues running for several seconds-therefore do not touch

the underside of the mower until the cutter has come to a standstill!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt GX 7000 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info