Bedienungsanleitung Blaupunkt KSSK 757302 (Seite 17 von 20) (Deutsch, Englisch)

716226

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Product Specications

Voltage 230 ~50 Hz

Motor 1400 W

No load speed 5400 rpm

Max Cut 90° 63.5mm

Blade Size 185mm 24T

Sound Pressure Level LPA 89 dB(A)

Sound Power Leve LWA 100 dB(A)

Vibration Level 1,5m/s 2

Weight 4,3 kg

Operating Instructions

Adjustments Depth Of Cut At 90° (Pic.9-12)

• The Circular Saw has an adjustable depth of cut. To adjust the depth of cut slacken the lever located on the side of the

machine (Pic.9).

• Measure the depth required from the base plate to the highest point of the blade or use the depth gauge on the ﬁxed guard.

(Pic.10).

Angle Of Cut 0-45° (Pic. 11)

• Located at the front of the machine is the 0-45° locking lever (Pic.11). Slacken the lever and the base plate assembly will rotate

between 0-45°. Set the desired cutting angle by using degree scale at the front of the machine and tighten the locking lever.

• At the front of the base plate there are two notches marked 90° and 45°. These notches are a guide to indicate the position of

the blade in relation to the cut being made in the material.

Parallel Cutting (Pic.12)

• This machine is supplied with a parallel cutting guide. This cutting guide is ﬁtted to the front of the machine and secured with

the locking knob (Pic.12).

Changing The Blade (Pics. 13 To 16)

• Always ensure that the Circular Saw is disconnected from the mains supply before carrying out any maintenance or

adjustments.

• The blade is extremely sharp and care must be observed when handling.

• Caution must be observed as the blade guard is spring loaded and if released may cause an injury. Rotate the blade guard into

the fully open position and secure it in this position using a screwdriver or piece of wood.

• Depress the spindle lock and using the supplied hex key, unscrew the hex socket screw in an anti-clockwise direction. (Pic.13

- 14)

• Remove the hex socket screw and the retaining ﬂange noting which way round the retaining ﬂange is ﬁtted (Pic.14). You can

now remove the blade.

• Do not dispose of the blade in house-hold waste, recycle correctly.

• Take note of the position of the inner ﬂange, if this should fall oﬀ it must be replaced as shown in (Pic.15).

• Remove any wood debris from around the motor spindle and the two ﬂanges.

• Fit the new blade as shown in (Pic.16) ensuring that the direction of rotation arrow on the blade corresponds with the

direction of rotation arrow on the ﬁxed guard. Replace the retaining ﬂange and blade bolt.

• Tighten the hex socket screw securely but do not over tighten.

• Check the tightness of the hex socket screw before, during and after each use.

• Remove the piece of wood or screwdriver that is holding it in the open position. Slowly release the guard so that it covers the

blade.

• Check the operation of the blade guard making sure that it operates correctly. The operation is complete and your machine

is ready for use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt KSSK 757302 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info