Bedienungsanleitung Blaupunkt Munchen CD 43 (Seite 13 von 15) (Englisch)

614605

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

München CD 43

Switching off the audible alarm

You can switch off the audible alarm in two

different ways:

a) Tune in to another (traffic) station by

● pressing the seek tuning rocker

switch or

● touching a preset button on which

a traffic station is stored.

b) Switch off the priority for traffic stations

● by pressing the ARI button C.

Setting the volume for the audible

alarm and the traffic messages

Should you wish to listen to traffic messages

only, you can turn down the volume of the set

and stay on standby at the same time. As

soon as a traffic info comes in, it will be

automatically put through at a preadjusted

volume, no matter if you have turned down

the volume completely or if you are listening

to a CD.

You can use the set’s DSC software to

match the message volume to your special

requirements (e.g. when having an additio-

nal amp connected or in case of very noisy

or quiet cars).

● Press the DSC button 7.

Display 9 d will show “ARI” and a

number between 1 and 9. The

programme’s volume now corresponds

to the volume of the traffic messages.

● If necessary, adjust the message volu-

me using rocker switch F and

● press the DSC button again.

The ARI message volume can be adjusted

separately for KeyCards 1 and 2.

Traffic messages during CD

operation

This set allows it to listen to a CD and at the

same time be prepared to listen to an inco-

ming traffic message. As soon as a messa-

ge comes in, CD playback will stop and the

message is put through.

To achieve this proceed as follows:

● Activate priority for traffic stations by

pressing the ARI button C.

Display 9 d will then show “ARI”.

● Tune in to one of the traffic stations for

your area.

● Now you can listen to a disk. Playback

will be interrupted when a message

comes in.

Automatic start of seek tuning operati-

When leaving the coverage area of the traf-

fic station while listening to a CD, the set will

automatically start searching for a new one.

Choosing the display colour

With the set’s DSC software you can adjust

the display’s basic colour to suit the colour of

the dashboard lighting of your car. You can

choose between orange or green.

To change the display colour, press the

following buttons one after another:

● DSC 7,

●

/ F until “COL” lights up in the

display,

● << >> G to change the colour and

finally

● DSC 7 again.

BEEP (after actuation of a but-

ton)

All functions which need to be activated by

pressing the respective button longer than 2

secs. can be confirmed with a beep signal.

This BEEP can be switched on or off.

For this, proceed as follows:

● Press DSC 7.

● Press / F until “BP” lights up in

display 9 a.

● Use << G to switch the BEEP on (“BP

1” in the display), and

● >> G to switch the BEEP off (“BP 0”

in the display).

This function can be adjusted separately for

KeyCards 1 and 2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt Munchen CD 43 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blaupunkt Munchen CD 43

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info