Bedienungsanleitung Blaupunkt Safe Drive SDC 2.0 (Seite 11 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

790587

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

Warranty

For products purchased within the European Union,

we provide a manufacturer‘s warranty. For devices

purchased outside the European Union, the warranty

conditions issued by our respective national represen-

tative apply.

The warranty conditions can be viewed at

www.blaupunkt.com, if no further information is given

here, the customary national legal provisions apply.

Service

Should you ever need a repair service, please contact

your Blaupunkt dealer. Further information on service

partners in your country can be found at www.blau-

punkt.com.

Replace Battery

If you operate the controller with a battery, it must be

replaced every 2-12 months (depending on usage).

Only use the battery type CR2032 / 3V:

Turn the battery compartment cover on the back of

the controller in the direction of the visible „OPEN“ ar-

row, using a straightened paper clip or needle to insert

it into the small hole in the lid, then carefully lift it o

without force.

Gently pry out the battery, avoid touching the contacts

or tabs.

Insert the new battery rst on the side with the con-

tacts (+ must be visible on the inserted battery) and

then gently push down on the opposite side until it

clicks into place.

Now replace the battery compartment cover and close

it.

Technical Data

Range

(Distance between

transmitter and receiver,

depends on environment): about 5- 10m

Power supply

Remote controller: 3V, CR2032/ 10.5 -14.4 V

Interface: 10.5 -14.4 V

Quiescent current: < 1mA

Troubleshooting

Below you will nd some error pictures and their possi-

ble solution. If you still have problems with the device,

contact your dealer or Blaupunkt Service. Please have

the installation checked or carried out by a specialist in

case of problems. Much of the problems that may arise

can be attributed to connection and operator errors.

• No function when pressing a key:

Please check the battery / power supply of the cont-

roller.

Please check the power supply of the interface.

Please check the cabling / connections.

• No or wrong function when pressing button(s):

Please re-learn the corresponding button(s) via the

menu in your car radio, please refer to the instructions

of your car radio.

• Rotary encoder does not work as desired/ programming

not possible at all:

Move the rotary encoder ⑨ during the teach-in pro-

cess only a step / click or a specic number of steps,

then check the function. Depending on the radio, it may

be necessary to program the volume to the ⑧ keys if

the encoder signals are not processed correctly. Then

use the rotary encoder for other functions such as title

jump / station change, etc..

Please try to change controller to the teach-in mode

(see chapter “Programming”)

• Remote control does not work after switching on the car

radio again and must always be reprogrammed:

Please check whether the radio is properly connected

to permanent power (battery).

Warranty | Service | Replace Battery | Technical data | Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt Safe Drive SDC 2.0 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info