Bedienungsanleitung Blaupunkt TravelPilot RNS 149 (Seite 3 von 8) (Englisch)

526056

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Installation instructions

3. Installing the antenna

Connect the antenna wiring to the en-

closed bracket(see Fig. 5).

3.1 Radio antenna

In pre-equipped vehicles (e.g.: VW,

Seat, Audi), the antenna gets its pow-

er supply via the antenna wire (see the

vehicle operating instructions). If you

want to replace the OEM radio with a

conventional radio, you will have to

order an antenna supply diplexer (Or-

der-No. 7 691 290 202) or the adapter

cable (Order-No. 7 607 621 129) from

your dealer. You will find information

on the installation and connection of

the antenna in the antenna installation

instructions. (see Fig. 5).

3.2 GPS antenna (satellite navigation)

You will find information on how to in-

stall the antenna in the enclosed an-

tenna installation instructions.

If the GPS antenna is installed inside

the vehicle, we cannot guarantee that

the system will function correctly.

4. Installing the TravelPilot

4.1 Setting the Gyro

Important: Before the TravelPilot is

inserted, the gyroscope must be put in

a horizontal position (see Fig. 8).

Important: Installation position of the

TravelPilot: right / left: min. 5˚/ max.

+5˚, front to back: min. -10˚ / max. +30˚

The TravelPilot is installed in the

standard car radio compartment pro-

vided by the manufacturer (see Fig. 5 ).

For vehicles without a DIN compart-

ment, Blaupunkt offers vehicle-specif-

ic installation kits for 50/52 mm units

for the most popular vehicle models.

Please check the installation condi-

tions in your vehicle and use a vehi-

cle-specific installation kit if necessary.

4.2 Installing the bracket

The bracket included with this Travel-

Pilot allows you to install the system in

vehicles with a DIN car radio compart-

ment measuring 182 x 53 x165 mm

and an instrument panel which is 1 to

20 mm in the area where the fastener

tabs are located, (see Fig. 1). For the

installation, you have to push the

bracket into the compartment and de-

termine which fastener tabs you can

bend over with a screwdriver (see

Fig. 6).

Note: Bend over as many of the fas-

tener tabs as possible.

4.3 Installing the TravelPilot

Push all of the plugs into the sockets

until they lock into place. Now insert

the navigation system from the front

into the bracket. Apply gentle pressure

to both side edges and push it in until

the spring locks snap into position on

the right and left (you will hear a loud

click).

Important! When you push in the sys-

tem, make sure that you do not put any

pressure on the display, the knobs or

the keys!

4.4 Removing the TravelPilot

Insert the handles into the correspond-

ing holes on the left and right side of

the front panel and push them in until

you hear a loud click (unlocking the

side spring locks). Use both handles

to carefully pull the TravelPilot out of

the compartment. Now you can pull

out the connection cables by applying

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt TravelPilot RNS 149 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blaupunkt TravelPilot RNS 149

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info