Bedienungsanleitung Blaupunkt VCC301 (Seite 7 von 76) (Englisch, Polnisch)

698412

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

1. Nozzles:

a) Multi-purpose brush nozzle

b) Crevice tool

c) Dust brush

2. Telescopic tube

3. Hose handle

3a. Suction power control on the hose

handle

4. Hose

5. Button: a) cord reel, b) power switch

PREPARATION OF THE VACUUM CLEANER FOR WORK

Make sure that the dust container of the vacuum cleaner is empty and the motor inlet filter is properly

installed. Insert the hose connector into the vacuum cleaner inlet and lock it. Connect the hose handle

with the telescopic tube or the nozzle. Put the appropriate nozzle on the telescopic tube. Grabbing the

plug unwind the power cord. The yellow band on the cord signals the end of the cord.

Connect the power plug to the wall socket. Turn on the vacuum cleaner with the switch button (6b).

WHEN THE VACUUM CLEANING IS DONE

Unplug the power cord from the wall socket. It is recommended that the cord be rewound by pressing

the cord reel button (6a). Make sure that the cable is loose, it is not blocked by anything and gently

hold the cord to prevent it from tangling and to avoid the strong impact of the plug on the housing.

Disconnect the nozzle, tube and hose. Clean these parts.

The vacuum cleaner may be stored in a vertical or horizontal position.

Be careful not to bend the hose excessively, this may result in its deformation or damage.

EMPTYING THE DUST CONTAINER

To remove the container, press the release button of the container (9b), while pulling the container

upwards and holding the handle of the container (9a).

Remove the inlet filter (9d) and clean it.

Holding the cover (9f ) and the container, press the opening lever (9e). Then open the cover (9f ) and

remove dirt from the container.

To re-install the container, the above steps must be performed in a reverse order. When re-installing

the air inlet filter (9d), pay attention to the position of the "no filter" safety blockade (9c).

CLEANING AND MAINTENANCE

Regularly clean the nozzles, the tube and the hose.

The body may be wiped with a slightly damp cloth, then it should be immediately wiped dry.

Whenever emptying the dust container, remove dirt from the inlet filter. It is recommended that the

filter be thoroughly washed under running water at regular intervals. After washing the filter, install it

only if it is completely dry.

It is recommended that the exhaust filter be replaced every 6-12 months depending on the intensity of

the use of the vacuum cleaner. To do this, open the exhaust filter cover and remove the old filter. Then

insert a new filter in place and close the cover of the exhaust filter by engaging the lower fastening

items and blocking the upper hook. The inlet filter must be replaced twice as often as the exhaust filter.

6. Exhaust grille

7. Hose connector

8. Holder

9. Dust container:

a) Container handle

b) Container release button

c) No filter safety blockade

d) Motor inlet filter

e) Container opening lever

f) Cover

VCC301

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt VCC301 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info