Bedienungsanleitung Blendtec CHEF 600 (Seite 18 von 156) (Englisch, Französisch, Spanisch)

626843

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

4.2 STEALTH 875™ & STEALTH 885™

4.2.1 Installation

Stealth Above Counter Installation

• Select a location that is near an electrical outlet� Also consider proximity to

ingredients, and patrons as well as available counter space�

• Place the blender on the counter in a spot where the air intake vents on the

sides and exhaust on the back of the blender are unobstructed�

• Ensure there is enough room above and around the unit to allow for unhampered

movement of the sound enclosure (see Figure 1 for measurements)�

• Plug the unit into an outlet with appropriate electrical protection�

Stealth In-Counter - Preparation for Installation

Note: You may locate your Blendtec Stealth in the same space as your previous

Blendtec in-counter blender. Just remember to ensure proper spacing for the

sound enclosure (see Figure 1 for measurements).

• Identify the desired blender location� Consider proximity to ingredients, and

patrons as well as available counter space� Also ensure that an electrical outlet

is readily accessible�

• Ensure the location meets all dimensional requirements (see Figures 1 and 3)�

• The countertop can be no thicker than ¾” (1�9 cm)� A thicker countertop will obstruct

motor ventilation�

• If installing more than one blender, allow 14”–16” (35�6 - 40�6 cm) of center-to-center

blender spacing�

• If installing a sound enclosure, allow a clearance of at least 5 ½” (14 cm) from the

sound enclosure to the wall and 26” (66 cm) from the countertop to any over-the-

counter cabinetry�

• Ensure lower cabinetry allows adequate airﬂow�

• The blender draws ambient air into the vent holes located on the lower back of

the motor and then evacuates hot air through the vents located on the lower front

and sides of the motor� For the motor to cool properly, a sufﬁcient amount of air

must be able to circulate around the motor�

• There should be at least 6 ½” (16�5 cm) of space from the countertop to the

next lower shelf of the cabinet, leaving a minimum space of 3” (7�6 cm) between

the bottom of the motor and the lower shelf� Cabinetry should not be closed; it

should allow air to ﬂow freely from the outside to the inside of the cabinet space�

• Plastic bags, cups, and so forth, should not be stored closer than 3” (7�6 cm) from

the bottom of the motor�

• Cut a hole in the countertop 4 ⅜“ (11�1 cm) wide and 5 ⅞” (14�9 cm) long (see the

countertop hole template in Appendix A)� Ensure that the 4 ⅜” (11�1 cm) sides are

parallel with the machine operator�

Note: Double check to ensure that all space requirements and measurements

are correct BEFORE cutting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blendtec CHEF 600 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blendtec CHEF 600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info