Bedienungsanleitung Blendtec CHEF 775 (Seite 5 von 19) (Englisch)

626841

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

• If installing more than one blender, allow 14”–16” (35�6 - 40�6 cm) of center-to-center

blender spacing�

• If installing a sound enclosure, allow a clearance of at least 5 ½” (14 cm) from the

sound enclosure to the wall and 26” (66 cm) from the countertop to any over-the-

counter cabinetry�

• Ensure lower cabinetry allows adequate airﬂow�

• The blender draws ambient air into the vent holes located on the lower back of

the motor and then evacuates hot air through the vents located on the lower front

and sides of the motor� For the motor to cool properly, a sufﬁcient amount of air

must be able to circulate around the motor�

• There should be at least 6 ½” (16�5 cm) of space from the countertop to the

next lower shelf of the cabinet, leaving a minimum space of 3” (7�6 cm) between

the bottom of the motor and the lower shelf� Cabinetry should not be closed; it

should allow air to ﬂow freely from the outside to the inside of the cabinet space�

• Plastic bags, cups, and so forth, should not be stored closer than 3” (7�6 cm) from

the bottom of the motor�

• Cut a hole in the countertop 4 ⅜“ (11�1 cm) wide and 5 ⅞” (14�9 cm) long (see the

countertop hole template in Appendix A)� Ensure that the 4 ⅜” (11�1 cm) sides are

parallel with the machine operator�

Note: Double check to ensure that all space requirements and measurements

are correct BEFORE cutting.

In-Counter Installation

• Feed the electrical cord through the hole in the countertop�

• Gently place the blender unit into the hole�

• Ensure the gasket is seated correctly, lying ﬂat against the counter surface and

not pinched by the housing�

• Plug the unit into an outlet with appropriate electrical protection�

Figure 3. Stealth In-Counter Clearance

3” (7.6 cm)

Minimum

clearance

¾” (1.9 cm)

Maximum

thickness

4.1.2 Stealth 875™ Quick Start Guide

1� Touch the power icon to turn on the blender�

2� Raise the sound enclosure lid�

3� Place the blender jar on the motor base, ensuring the jar is completely seated

and the jar lid is secured�

4� Close the sound enclosure lid�

5� On the control surface, touch the desired blend cycle number, pulse icon or

desired location on the slider control bar�

6� To stop a blend cycle before the programmed time elapses, press the

cancel/exit button� If you have enabled the Blend Cycle Pause feature, press

the previously selected blend cycle button to pause the cycle� To resume

the paused cycle, press the previously selected blend cycle button again�

4.1.3 Stealth 885™ Quick Start Guide

1� Press the power icon to turn on the blender�

2� Raise the sound enclosure lid�

3� Place the blender jar on the motor base, ensuring the jar is completely seated

and the jar lid is secured�

4� Close the sound enclosure lid�

5� On the control surface, press the desired blend cycle number or pulse icon�

6� To stop a blend cycle before the programmed time elapses, press the

cancel/exit button� If you have enabled the Blend Cycle Pause feature, press

the previously selected blend cycle button to pause the cycle� To resume

the paused cycle, press the previously selected blend cycle button again�

4.1.4 Automatic Cycle Operation

Your Stealth blender is preprogrammed with multiple blender proﬁles to help

operators achieve consistent blends with a minimum of training, trial, and error�

You can select from the following proﬁles and blend cycles:

Scroll (visible in programming mode)

Power Cancel/Exit

Mode

Slider Control Bar

Preprogrammed Cycle Buttons

Pulse

Select (visible in programming mode)

Scroll

Power

Cancel/Exit

Preprogrammed Cycle Buttons

Pulse

Select

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blendtec CHEF 775 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blendtec CHEF 775

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info