Bedienungsanleitung Blendtec CONNOISSEUR 825 (Seite 50 von 156) (Englisch, Französisch, Spanisch)

626840

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

• Error: Touch controller output is invalid

CONNOISSEUR 825™

Overtemp Error — This indicates that the motor is overheating� The blender

has been disabled until the unit cools to operating temperatures� If the

blender does not work after 20 minutes or more of cooling time, please

call your Blendtec Service Agent�

Overload Error — This indicates an overload on the motor�

1� Clear the error message by pressing any button or turning the blender off and

on again�

2� Remove the jar, and run the blender to determine whether the issue relates to

the jar or the motor�

3� With the jar removed, check for blockage in or around the socket on the motor

base and the blade assembly on the jar�

4� Place the jar securely on the motor base, and touch to pulse the blade through

the mixture�

5� Ensure the jar is not loaded with excessively hard or thick ingredients�

If overload condition re-occurs, contact your Blendtec service agent�

A “Watchdog Timeout” error indicates a disruption in the normal operation of

the electronic blender controls� This is an uncommon error message, which is

usually caused by incoming power ﬂuctuations or spikes� This error message is

cleared by turning off the blender for 10 seconds (using the switch), then turning

back on� If this error is displayed immediately on start-up, or if it occurs regularly

during normal use contact your Blendtec service center for assistance�

CHEF 775™

Overtemp Error — This indicates that the motor is overheating� The blender has been

disabled until the unit cools to operating temperatures� If the icon does not disappear

after 20 minutes or more of cooling time, please call your Blendtec Service Agent�

Touch Error — This indicates that more than one touch sensor on the blender has

been touched� To avoid this message, touch the center of the desired button�

If this icon remains on when no one is touching the touch area, unplug and re-plug

in the blender� If the problem persists please contact your Blendtec Service Agent�

Overload Error — This indicates an overload on the motor�

1� Clear the error message by pressing any button or turning the blender off and

on again�

2� Remove the jar, and run the blender to determine whether the issue relates to

the jar or the motor�

3� With the jar removed, check for blockage in or around the socket on the motor

base and the blade assembly on the jar�

4� Place the jar securely on the motor base, and touch to pulse the blade through

the mixture�

5� Ensure the jar is not loaded with excessively hard or thick ingredients�

If overload condition re-occurs, contact your Blendtec service agent�

Reset Errors — If this message appears on the LED information center it indicates

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blendtec CONNOISSEUR 825 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blendtec CONNOISSEUR 825

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info